Kenton Pro-2000 MkII - Manual (Page 16)

15
specified memory location and also to the edit buffer (current setup)
the data will be immediately utilised and the display will be updated.
You may change the block number of a memory dump without causing any
problem. For example, data that came from memory 6 could be returned to
the current setup by merely changing the 06 in byte [ 7 ] to a 00.
Parameter data are stored in the following addresses.
Address
Function Range Notes ( see end )
00h
A Receive chan 0 - 15 { 1 }
01h A note priority 0 - 2
02h A trig / retrig 0 - 1
03h A transpose 232 > 0 > 24 { 2 }
04h A pitchbend range 0 - 24
05h A portamento speed 0 - 255
06h A portamento cont # 252 - 0 - 119 { 3 }
07h A lfo depth controller # 252 - 0 - 119 { 4 }
08h A lfo max val 0 - 127
09h A lfo assign 0 - 1
0Ah A gate select 0 - 7 5 modes used
0Bh A fine tune val 129 > 0 > 127 129>0 = -ve
0Ch A scale val 129 > 0 > 127 129>0 = -ve
0Dh A v/o – hzv – 1.2v select 0 - 2
0Eh
B Receive chan 0 - 15 { 1 }
0Fh B note priority 0 - 2
10h B trig / retrig 0 - 1
11h B transpose 232 > 0 > 24 { 2 }
12h B pitchbend range 0 - 24
13h B portamento speed 0 - 255
14h B portamento cont # 252 - 0 - 119 { 3 }
15h B lfo depth controller # 252 - 0 - 119 { 4 }
16h B lfo max val 0 - 127
17h B lfo assign 0 - 1
18h B gate select 0 - 7 5 modes used
19h B fine tune val 129 > 0 > 127 129>0 = -ve
1Ah B scale val 129 > 0 > 127 129>0 = -ve
1Bh B v/o – hzv – 1.2v select 0 - 2
1Ch
C Receive chan 0 - 15 { 1 }
1Dh C Transmit chan 0 - 15 { 1 }
1Eh D Receive chan 0 - 15 { 1 }
1Fh D kadi / wasp select 0 - 1
20h
Ax1 Receive chan 0 - 15 { 1 }
21h Ax1 Cont # 239 > 0 > 119 { 6 }
22h Ax1 min val / fine tune 0 > 64 > 127 { 5 }
23h Ax1 max val / scale 0 > 64 > 127 { 5 }
24h Ax1 reset val 0 > 64 > 127 { 5 }
25h Ax1 lfo cont # 252 - 0 - 119 { 4 }
26h Ax1 lfo max val 0 - 127
27h Ax1 lfo assign 0 - 1
28h
Ax2 Receive chan 0 - 15 { 1 }
29h Ax2 Cont # 239 > 0 > 119 { 6 }
2Ah Ax2 min val / fine tune 0 > 64 > 127 { 5 }