Operating the computer [measuring screen – CatEye CYCLOCOMPUTER CC-COM10W User Manual

Page 2

Advertising

MODE

Operating the computer [Measuring screen]

Starting/Stopping measurement

Measurements start automatically

when the bicycle is in motion. During

measurement, km/h or mph ﬂ ashes.

Switching computer function

As shown in the figure, pressing

MODE changes the measurement

data at the top/bottom row display.

Resetting data

Pressing and holding MODE on the measuring

screen returns the measurement data to 0.

Backlight

Pressing LIGHT turns on the screen

illumination for about 3 seconds.

Pressing any button while backlight is still on

extends the illumination for another 3 seconds.

Night mode ( )

Pressing and holding LIGHT turns on ,

night mode will activate. Night mode is a

function to control the screen illumination

by pressing MODE. Pressing MODE turns

on the illumination, and pressing it again

changes the selected mode. While is

turned on, if you press and hold LIGHT, or

the computer does not receive a signal for

10 minutes, night mode will be turned off.

Power-saving mode

If the computer has not received a

signal for 10 minutes, power-saving

mode will activate and only the date/

clock will be displayed. When you

press MODE, or the computer re-

ceives a sensor signal, the measuring

screen reappears. If another 60 minutes of inactivity elapses, SLEEP will be displayed on

the screen. With the SLEEP display, pressing MODE returns to the measuring screen.

ETA estimated time of arrival and progress graph

When you set the distance from your departure point to your destination point, the estimated

time of arrival at the destination point will be estimated and displayed based on the remain-

ing distance and the average speed, and the progress in distance is displayed in a graph.

Estimated time of arrival (

)

To set the target trip distance, you can select automatic setting or manual setting.

Automatic setting (

•

AUTO)

Once you perform the resetting operation, the trip distance just before resetting is

automatically set as a target trip distance.

Automatic setting is applied once you change the “Target trip distance setting” on the Menu screen

to AUTO. For the setting procedure, refer to the “Target trip distance setting” on the Menu screen.

Manual setting (

•

MANU)

The distance from your departure point to your destination point is set manually

from the “Target trip distance setting” on the Menu screen.

For the setting procedure, refer to the “Target trip distance setting” on the Menu screen.

When the estimated time of arrival is estimated to be after 24 hours, the estimated time of arrival

display changes to ET. When the estimated time of arrival is estimated to be within 24 hours, it

returns to the estimated time of arrival display.
The estimated time of arrival is not fi xed, but changes according to the trip conditions (speed, stop, etc.).

When the unit reaches the target trip distance, it changes to the

ETA screen regardless of the

measuring screen displayed, and then returns to the original measuring screen in 5 seconds after

notifying the arrival. The ETA “Estimated time of arrival” stops while displaying the current time;

however, the computer continues measuring.

ETA progress graph

Once the target trip distance is set, you can view the progress in a graph, where the

distance from your departure point to your destination point is divided into 10 seg-

ments. The current progress position appears and ﬂ ashes.

Data view (DST VIEW / CO2 VIEW)

This unit automatically saves the trip distance and the Carbon offset, which can be viewed

for the day, week, month, year, and total.

Data view's contents and update timing

Trip distance and the Carbon offset saved are updated at 0:00 in the morning. The

update timing for the day, week, month, and year is as follows.

Item

Description

DAY

Trip distance per day. Data can be viewed for today and yesterday.

At the time of updating at 0:00 in the morning, the unit saves yesterday's data, and dis-

cards the data for the day before yesterday.

WEEK

The data for every 7 days starting from January 1st, regardless of the day of the week, is

stored as data for the week. Data can be viewed for this week and last week.

At the time of updating every 7 days, the unit stores the data for last week, and discards

the data for the week before the last week.

MON

The data starting from the 1st to the end of the month is stored as data for the month. Data

can be viewed for this month and last month.

At the time of updating at the beginning of a month, the unit stores the data for last month,

and discards the data for the month before the last month.

YEAR

The data starting from January 1st to December 31st is stored as data for the year. Data

can be viewed for this year and last year.

At the time of updating on January 1st, the unit saves the data for last year, and discards

the data for the year before the last year.

TOTAL

The total trip distance (Total Distance) can be viewed and the total Carbon offset since the

computer started measuring.

When the total distance is entered manually, the entered value is reﬂ ected.

How to calculate the Carbon offset (CO2 VIEW)

The Carbon offset are calculated as follows.

Trip distance (km) x 0.15 = Carbon offset (kg)

This factor of 0.15 is determined by applying the average value of the overall gasoline-powered

passenger cars in 2008 to the equation of the “Carbon offset from 1km drive of a gasoline-powered

car” described on the website of the Ministry of Land, Infrastructure and Transport and Tourism.

DST VIEW (Data view: Distance)

The trip distance is displayed for the day, week, month, year, and total.

Viewing the data view and changing the settings [Menu screen]

Pressing MENU on the measuring screen moves to the menu screen for setup change. With

the Menu screen, you can view the data view, and change the computer settings. Press MODE

to change to the item of interest, and then press and hold MODE to select the menu item.

For details of

DST VIEW and CO2 VIEW, refer to the “Data view”.

Clock setting

When MODE is pressed and held, “Display format”, “Hour”, and “Min-

ute” will appear, in this order.

When

12h is selected, “AM/PM selection” is required.

Speed/temperature unit selection

Select “km/h” or “mph” for the speed unit, and “°C” or “°F” for the

temperature unit.

After changing the unit, it is necessary to perform the resetting operation.

Date format setting

Select the date display format from “D/M (day and month)” or “M/D

(month and day)”.

The date cannot be changed. When the date must be changed, perform the

“restarting operation”, and follow the relevant procedure.

Tire size entry

Enter the tire circumference of your bicycle in mm. Pressing MODE in-

creases the value, and pressing and holding MODE moves to the next digit.

(Setting range: 0100 – 3999 mm)

Refer to the tire circumference reference table.

Target trip distance setting

Set the target trip distance for calculating the ETA. Press MODE to

select “AUTO (automatic setting)” or “MANU (manual setting)”. When

MANU is selected, fi rst long press the MODE button to ﬂ ash the fi gures.

Then press MODE to increase the value. Shift the digit by long pressing

the MODE button. (Setting range: 0 – 999 km [mile])

Refer to “Estimated time of arrival” for details.

It is necessary to perform the resetting operation in advance. Refer to “Reset-

ting data”.

CO2 VIEW (Data view: Carbon offset)

The Carbon offset are displayed for the day, week, month, year, and total.

MODE

Setting screen

Data view

All the distance displays up to 99999 km or mile in integral number except

for today and yesterday.

Total elapsed time displays up to 9999 hours.

All the carbon offset displays up to 99999 kg in integral number except for

today, yesterday, this and last week.

MODE

(press

& hold)

(press

& hold)

: Pace arrow

Indicates whether the cur-

rent speed is faster ( ) or

slower ( ) than the aver-

age speed.

: Night mode icon

: Computer battery icon

Selected mode at the middle row

ETA progress graph

Temperature display

-20 – 60 ˚C

Clock display

AM1:00 – PM12:59 [0:00 – 23:59]

With the measuring screen, the clock

and the temperature are always dis-

played at the bottom row.

Data at the top row display

The ETA estimated time of arrival

or current speed is displayed.

*1 With the computer installed to the bracket, press

the marking section on the computer.

*2 When Tm exceeds about 27 hours or Dst exceeds

999.99 km, the average speed display turns to .E,

thus it cannot be measured. Reset the data.

During measurement, or if the computer receives a sensor

signal, the unit does not switch to the setting screen.
After changing, be sure to press

MENU to register the setting.

If the setting screen is not touched for a minute, the mea-

suring screen appears without changing of any settings.

MODE

(press & hold)

ETA Estimated time

of arrival

AM1:00 – PM12:59

[0:00 – 23:59]

SPD

Current speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.5 mph]

AVS

Average Speed *2

0.0 – 99.9 km/h

[0.0 – 62.5 mph]

MXS

Maximum Speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.5 mph]

Elapsed Time

0:00'00 – 9:59'59

DST

Trip Distance

0.00 – 999.99 km [mile]

Today

Date

Week

Month

Year

Total elapsed time

This week

This month

This year

Total

MENU

Press and hold

MODE on any screen to view past data (yesterday,

last week, last month, last year). Pressing MODE again returns

to the current data.
Selecting Total allows you to also view the total elapsed time.

Advertising

Popular Brands

Popular manuals