Milwaukee Tool 6185-20 - Manual (Page 3)

4 5
FUNCTIONAL DESCRIPTION
SYMBOLOGY
SPECIFICATIONS
Cut-Off Machine Capacities Abrasive Cut-Off Wheel Capacities
Cat. No.
Wheel
Size RPM
Volts
AC/DC Amps
Spindle
Size
Cutting
Capacity
Wheel
Size
Min.
Wheel
RPM
Rating
Wheel
Thickness
Wheel
Arbor
Hole Size*
6185-20 14" 4600 120 15 5/8"-11 4-7/16" 14" 5400 1/8" 1" or 20 mm
Safety Warnings Specifi c for Abrasive Cutting-
Off Operations:
• Use only wheel types that are recommended
for your power tool and the specifi c guard
designed for the selected wheel. Wheels for
which the power tool was not designed can not
be adequately guarded and are unsafe.
• The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed to-
wards the operator. The guard helps to protect
operator from broken wheel fragments and ac-
cidental contact with wheel.
• Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
• Always use undamaged wheel fl anges that are
of correct size and shape for your selected
wheel. Proper wheel fl anges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel fl anges.
• Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller tool
and may burst.
Additional Safety Warnings Specifi c for Abra-
sive Cutting-Off Operations:
• Do not jam the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases
the loading and susceptibility to twisting or bind-
ing of the wheel in the cut and the possibility of
kickback or wheel breakage.
• Do not position your body in line with and
behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your
body, the possible kickback may propel the spin-
ning wheel and the power tool directly at you.
• When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
• Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
• Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
• Use extra caution when making a “pocketcut”
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
Additional Safety Warnings
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.
WARNING To reduce the risk of injury,
avoid inhalation of dust generated by grind-
ing and cutting operations. Exposure to dust
may cause respiratory ailments. Use approved
NIOSH or OSHA respirators, safety glasses or
face shields, gloves and protective clothing.
Provide adequate ventilation to eliminate dust,
or to maintain dust level below the Threshold
Limit Value for nuisance dust as classifi ed
by OSHA.
* The tool is supplied with both a 1" fl ange nut and a 20 mm fl ange nut. To ensure the wheel is properly secured,
always use the fl ange nut that matches the wheel arbor hole size.
1. Trigger
2. Overload protector
3. Guard
4. Shoe assembly
5. Abrasive cut-off wheel
(not included)
6 7
9
8
3
1
2
5
4
6. Handle
7. Spindle lock
8. Wing nuts
9. Guard bolt
Amps
No Load Revolutions per
Minute (RPM)
Volts
Underwriters Laboratories, Inc.,
United States and Canada
Alternating Current/Direct Current Mexican Safety Standards