Perfect Aire 10000PPAC - Manual (Page 7)

OPERATING INSTRUCTIONS
- Press the "MODE" button until the "COOL"
indicator light comes on.
- Press the ADJUST buttons " " or " " to
select your desired room temperature. The
temperature can be set within a range of
62 O F-88 O F/17 O C-30 O C.
- Press the "FAN" button to choose the
fan speed.
- Press the "MODE" button until the "DRY"
indicator light comes on.
- Under this mode, you cannot select a fan speed
or adjust the temperature.
- Keep windows and doors closed for
dehumidifying effect.
- Remove exhaust hose. (See page 11.)
COOL operation
DRY operation
- Press the "MODE" button until the "FAN"
indicator light comes on.
- Press the "FAN" button to choose the fan
speed. The temperature cannot be adjusted.
- Remove exhaust hose. (See page 11.)
FAN operation
FOLLOW ME
AUTO operation
- When you set the air conditioner in AUTO mode,
it will automatically select cooling or fan
only operation.
- The air conditioner will control room temperature
automatically around the temperature you have set.
- Under AUTO mode, you cannot select the
fan speed.
This feature can be activated from the remote
control ONLY. The remote control serves as a
remote thermostat allowing for the precise
temperature control at its location.
To activate the FOLLOW ME feature, point the
remote control towards the unit and press the
FOLLOW ME button. The light on the unit control
panel will illuminate to indicate it received the signal.
It will continue to send this signal until the feature is
deactivated by pressing the FOLLOW ME button
again. If the unit does not receive the Follow Me
signal during any 7 minute interval, the unit will beep
to indicate the Follow Me mode has ended. The
display on the remote control indicates the
temperature at the remote ONLY.
SLEEP operation
In this mode the selected temperature will
increase by 2 O F/1 O C 30 minutes after the mode
is selected.The temperature will then increase
by another 2 O F/1 O C after an additional 30
minutes. This new temperature will be
maintained for 7 hours before it returns to the
originally selected temperature. This ends the
Sleep mode and the unit will continue to operate
as originally programmed. NOTE: This feature is
not available under FAN or DRY mode.
After the unit has stopped, operation cannot be
restarted in the first 3 minutes. This is to protect
the unit. Operation will automatically start after
3 minutes.
Wait 3 minutes before resuming operation.
AIR FLOW DIRECTION ADJUSTMENT
If the unit breaks off unexpectedly due to the
power being cut,it will restart with the previous
function setting automatically when the power
is restored.
- The louver can be set to the desired position
manually. (See Fig. 5 below.) The maximum
setting angle is approximately 60 O . Please do
not force it to open any larger.
- Do not place heavy objects or other loads onto
the louver. Doing so will damage the unit.
AUTO-RESTART
Fig. 5
6
TIMER operation
If setting the timer when the unit is on:
First press the TIMER button; the TIMER OFF
indicator light illuminates. It indicates the Auto Stop
program is initiated. Press the TIMER button again;
the TIMER ON indicator light illuminates. It
indicates the Auto Start program is initiated.
If setting the timer when the unit is off:
First press the TIMER button; the TIMER ON
indicator light illuminates. It indicates the Auto Start
program is initiated. Press the TIMER button again;
the TIMER OFF indicator light illuminates. It
indicates the Auto Stop program is initiated.
- Press or hold the UP or DOWN button to change
the Auto time by 0.5 hour increments, up to 10 hours
then at 1 hour increments up to 24 hours. The control
will count down the time remaining until start.
- The selected time will register in 5 seconds and
the system will automatically revert back to
displaying the previous temperature setting.
- Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timed program.
- When the malfunction (E1 or E2) occurs, the Auto
Start/Stop timed program will also be cancelled.