Veracity TIMENET - Manual

INSTALLATION (2)
1. Connect the network cable.
TIMENET consumes under 3W and provides a Class I
POE signature.
2. If your network is NOT POE, then you must also connect the
alternative 12V DC power (24V AC source is also compatible).
3. The amber LED will blink twice and then stay on.
After approximately 30 seconds, the unit will be running and
the green LED will blink with short pulses.
This indicates normal running with no GPS signal lock.
4. Connect the GPS antenna cable supplied with the unit and
ensure that the cable connector is fully screwed on.
5. After a few minutes (assuming the GPS antenna has been
properly mounted and connected) the green LED will switch to
a long pulse, indicating GPS signal lock.
NB: Depending upon the positioning of the antenna with respect
to the view of the sky, it may take longer to gain signal lock.
SOFTWARE & COPYRIGHT NOTICES
This manual is © Veracity 2012.
TIMENET contains open source products released under GPL V2 or similar license.
The relevant products can be downloaded for free from the following locations, or be
provided by Veracity UK Ltd for a fee, upon request to [email protected]
• Linux http://www.kernel.org/
• NTP Server http://www.ntp.org/
•
jQuery http://www.jquery.com/
• BusyBox http://www.busybox.net/
•
jQuery Impromptu http://www.trentrichardson.com/Impromptu/
• overLIB http://www.bosrup.com/web/overlib/
EC DECLARATION OF CONFORMITY
In accordance with EN 45014:1998
We, Veracity UK Ltd. of Prestwick International Aerospace Park, 4 Dow Road, Prestwick,
KA9 2TU, United Kingdom, declare that the equipment TIMENET GPS Master NTP
Time Server model number VTN-TN conforms to the essential protection requirements
of the EMC Directive 89/336/EEC as amended.
The product conforms with the following standards: EN 55022:2006 including
Amendment 1:2007. EN 55024:1998 including Amendment 2:2003
I hereby declare that the equipment named above has been been found to comply with
the relevant sections of the above referenced specifications. The unit complies with all
essential requirements of the EMC Directive.
Responsible Person
Mr Alastair McLeod, Director
Issued 4th January 2012 at Prestwick. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
RoHS
Reset Button
POE or Ethernet
Optional 12V DC Power
GPS Antenna
INSTALLATION (1)
TIMENET should only be installed:
• indoors, or :
• inside an appropriately IP-rated enclosure
TIMENET should be safely located, either :
• on a shelf, or :
• mounted to a wall
NB :
TIMENET should not be supported only by the attached cables.
The GPS antenna must be positioned in a location that has a clear
view of the sky. It can be mounted, either :
• on a window, using the adhesive pad supplied
(first clean the glass, using the alcohol pad supplied) or :
• on a metal surface, using the magnetic antenna pod
Should you require additional length on the antenna cable,
please use TIMENET antenna 10m extender,
partcode : VTN - EXTEND
TIMENET should only be powered by :
• a suitable POE network, or :
• a Class II isolated 12V DC power supply, or :
• 24V AC power supply
GPS MASTER NTP TIME SERVER
QUICK START GUIDE