SINGER 148-4 - Manual (Page 18)

36 PAirrS FOR MACHINE No. 148-7
NO. ri.ATK N.AME
5Ü1381'' ÍI133 Thread (upper) Controller Set Screw. . .
128250 9133 “ “ “ Thread Cuide
128251 9136
Poat with 501381)....................................
175 f 9102 'riiread (upper) (.’oiitroller d'liread (hade
Po.st Screw...............................................
50138 9133 Thread (upper) Controller'I'liread Cuido
Set Screw..................................................
128110 9136 Thread (upper) Check Spring.......
128111 9136
“ ‘‘ “ “ .\djusting
Plate..........................................................
22t)i) 9117 Thread (u])per) Check Siiring .Viljuating
Plate Screw...............................................
128112 9101 Thread (upi>er) Check S|)ring Regulating
Stud...........................................................
447c 9118 4’hread (upper) Check Spring Ri'gulating
Stud Set Screw..........................................
128252 9136 'I'liread (u|)per) 'I'ake-up..................
217 d 9117 “ “ “ Screw.......................
128253 9136 “ “ “ Stripper..............
128254 9136 “ “ “ “ liracket
1492i) 9117
Screw........................................................
226i) 9117 'rhread (upper) 4'ake-up St ripper Screw
128255 9125 'I'hroat Plate for 128202..................................
128418 9703
“ “ 128 112............................
N otk : When ordering Noa. 128255 and 128418,
slate gauge.
1319 k 9118 'I'luoat Plate Screw...........................................
IRON BASE
NO. 1'1.,\TE N.tME
128116 9119 Machine Rase with 301c, 307c, 448c,
1513.1, 27795, two each 935a, 42088,
66707 and three wood screw.s l .Cj in.
No. 12...............................................' . . .
42088 9121 Machine (.¡u.shion (felt)..................................
935i) 9121 “ “ Screw....................................
66707 9121 “ “ “ Wa.sher..................
3l)4c 9121 “ Screw Centre (lc4't).............................
1513,1 9121 “ “ ■' “ Nut.................
307c 9140 “ “ “ (right)...................
448c 9116 “ “ “ “ Set Screw
27795 9140
W’asher.....................................................
37
NO. PLATE
1407w 5563
14Ü8W 5563
14063 9140
9842 9121
120344 6375
120345 6375
26026 6375
26485 6375
120341 6375
4822 6375
8908 6375
8909 9140
ACCESSORIES
NAME
Machine Thumb Screw, for 3 in. table.
“ “ “ “ 2 in. table..
“ “ “ Spring..............
“ “ “ “ Washer.
Oiler (copper plated) with 120345.............
“ Spout 5 in. long....................................
Screw Driver (large)...................................
“ “ (small).....................................
Tweezers (curved)......................................
Wrench for 1521 and 1547........................
“ “ 1664, 1722 and 1723..............
“ “ 1513........................................
BELT GUARD
NO. PL-ATE N.AME
128171 9119 Belt Guard (lower).............................
128172 9119
“ “ (upper).............................
63505 9121 “ “ “ Hinge Pin..............
743382 9121 “ “ “ Lock Spring.......
2273 9121 “ “ “ “ “ Position
Pin.............................................................
331i) oils Belt Guard (upper) Lock Siiriiig Screw.
128173 ------Belt Guard complete, Nos. 331i), 2273,
63505, 128171, 128172, 743382, and
three wood screws 1 in. No. 10................
FOOT LIFTER PART^
NO. I'L.Vl'E N.VME
6439 --------Ghain, 36 in. to 45 in., with 56864 and
56865........................................................
N ote ; When ordering No. 6439, give length rec|uired.
4879 9121 Ghain Gonnecling Link.....................................
56864 9121 “ Hook (largei......................................
56865 9121 “ “ (.small).......................................
126249 9137 'Preadle...............................................................
4882 9121 “ Shaft.............................................
1262.50 9140 “ Spring............................................
126251 9137 “ Stand............................................
126252 9137 'Phreadle complete. Nos. 4882, 126249 to
126251 and two wood screws 1 in.
No. 16.......................................................