SINGER 114-34 - Manual (Page 17)

32
33
ATTACHMENTS AND ACCESSORIES
MACHINE No. 114-35
For Sewing Two or Four Hole Flat Buttons, from 10 to 50
ligne. Makes two parallel bars in four hole buttons, 21 stitches,
including cross and fastening stitches. Thread cutter. Clamp
vibrates UP the cylinder. Will hold button and material up to
inch thick and can be adjusted for buttons with holes %4
inch to inch apart. Speed 1500 R. P. M.
NOTE: THIS MACHINE IS THE SAME AS THE NO. 114-33
MACHINE, WITH THE FOLLOWING EXCEPTIONS:
Name
Feed Cam with 1901, 17874, 124841, two
each 1192C, 124973 and six 335J, In
place of 124924.......................................................
Feed Cara Driving Worm with 1441C and
1442C, In place of 124925......................................
Feed Cam Driving Worm Wheel with 463C,ln
place of 124926....................... '...............................
Feed Cam Shaft 59728 with 1653C and
17997, In place of 124931.......................................
Thread Nipper (lower) Cam, In place of
124929.....................................................................
Thread Nipper (Icwer) Lever Guide, In
place of 124900.......................................................
' 1
No.
124937
Plate
23185
39231 23181
17997 23185
124954 ..........
124841 23185
124973 23185
No.
59797
124958
18420
18423
Plate
23174
23157
23157
23157
Narae
Button Tray with two wood screws 11/4
In. No. 14..................................................................
Cylinder Base Plate with two 453C...................................
" * “ Hinge Connection....
“ " • " " Hinge
Pin..............................................................................
453C 23157 Cylinder Base Plate Hinge Connection
Hinge Pin Set Screw.................................................
134E 23157 Cylinder Base Plate Screw.................................................
124959 23157 Cylinder Base Plate (hinged) complete.
Nos 124958, two each 18420, 18423,
three wood screws 1 1/4 In. No. 12
and four 134E.........................................................
124975 Cylinder BaseyPlate 124959 with 124966..
124960 23157 Machine Supporting Braclcet (lower)............................
178J 23157 I t “ " " Screw
124961 23157 N " " (upper)............................................
1396J 23157
tl
" “ “ Screw
124962 23157 H " Link (lower)......................................
124963 23157
n
“ " (upper)............................................
124964 23157 M " " Hinge Rivet....................................
124965 23157
■
" ‘ Lock Plate.......................................
190333 23157 H • . « . Logi^
Stud...................................................................... .. .
124964 23157 Machine Supporting Link Lock Plate Rivet
124966 23157 Machine Support complete. Nos. 178J,
1396J, 124960 to 124963, 124965,
19C633 and four 124964..........................................
120346 23157 Oiler (copper plated) with 120047.......
120347 23157 " Spout, 8 1/2 In. long..................................................
11831 23157 Screw Driver (large)...........................................................
26026 23157
U
“ (small).........................................................
4822 23157 Wrench for 1547..............................................................
10875 23157 I f " 1518,1520,1649,1650 and 1662.
17905 23157
n
' 1176,1178,1654,1655 and 1676.
252Ö0 23157
n
" 1527..............................................................
27662 23157
0
" 1254 and 1508..............................................
Wo