Troy-Bilt 12204-10HP - Manual (Page 53)

MODELS 12089, 12090, 12204
Parts List
REF
No.
PART
No. DESCRIPTION QTY.
TRANSMISSION COVER & SHIFT LEVER
BRACKET ASSEMBLIES
1186299 Bolt-hex hd., #10-32 x 3/8",
self-locking flange........... 3
9463 Knob-tines/PTO clutch lever,
tapered, plastic................. 1
2263 Detent Plate-tines/PTO clutch lever
(incI.Ref. No. 4)................. 1
1900758 Decal-operating instructions,
detent plate....................... 1
1186347 Bolt-flanged hex hd.,
3/8-16x1-1/2"..................... 4
1186329 Bolt-flanged hex hd.,
5/16-18x3/4", Grades......... 1
1107382 Washer-flat, 5/16", S.A.E........ 1
1900870001 Bracket-shift levers (incl. Ref.
No. 86)................................. 1
9362 Pin-spring, 1/8"..................... 1
9838 Nut-castle (slotted), 1/2"-20, call
Tech Service for tightening
instructions...................... 1
9934 Washer-shoulder, 1/2"......... 1
9932 Washer-disc spring.............. 2
Lever-wheel speed shift (see page
51, Ref. No. 5for part number). 1
1900869001 Cover-power unit transmission.... 1
2566
Cover-power unit transmission
(incl. Ref. No.’s 18,19, 20, 21,22,
23 and 24)......................... 1
1123 Gasket-transmission cover... 1
1100045 Bolt-hex hd., 5/16-18x1 ”, Grade 5,
(remove with care)........... 1
1186230 Nut-hex, 5/16"-18.................. 1
1901439 Spring-neutral plunger (remove
with care).......................... 1
1035 Plunger-neutral (remove with care)
(incl. Ref. No. 22)............. 1
1901440 Clip Ring-retains neutral plunger.. 1
1186393 Nut-hex, flange locknut, 3/8"-16... 1
1902004 Bolt-hex hd., 3/8-16x1-1/2",
threaded full length......... 1
9
10
11
12
13
14
15
16
16A
17
18
19
20
21
22
23
24
25
26
27
TINES/PTO CLUTCH LEVER ASSEMBLY
1900878001 Lever-eccentric, tines/PTO clutch.
(also see Ref. No.’s 1,2,3 and
4 listed above)..................... 1
1100804 Bolt-hex hd., 1/4-20 x 1/2".......... 1
2123 Bushing-tines/PTO clutch lever
eccentric shaft.................... 1
REF
No.
PART
No. DESCRIPTION QTY.
28
29
30
31
33
34
35
36
37
38
39
40
42
43
44
45
45
45
45
46
47
48
49
50
51
52
53
9516 Retaining Ring-(snap ring),
external................................. 2
2461 Eccentric-shaft, tines/PTO clutch
lever...................................... 1
9911 Lockwasher-hi-collar, 1/4".... 1
9672 Screw-socket hd., 1/4-20 x 3/8“... 1
DRIVE SHAFT ASSEMBLY
9500 Retaining Ring-external......... 1
1909139 Dog Clutch-power unit........... 1
9301 Key-3/16sq.x1"......................... 3
1100004 Bolt-hex hd., 5/16-24 x 3/4", self­
locking flange. Grade 5....... 1
9944 Washer-disc spring (concave)....... 1
2107 Pulley-transmission drive, cast iron 1
50027 Washer-flat, hardened shoulder
1-1/4”..................................... 1
1186310 Bolt-hex hd., 1/4-20 x 3/4", front
bearing cap........................... 3
1900879001 Cap-front bearing................. 1
1983632
Seal-oil, front bearing cap..... 1
1124-2 Gasket-front bearing cap....... 1
1224-1 Shim-front bearing cap,.
010" thick........................ As Req'd
1224-2 Shim-as above, .030".................. As Req'd
1224-3 Shim-as above, .005"...................As Req'd
1224-4 Shim-as above, .062"......As Req'd
1714 Bearing & Cup-tapered cone roller
bearing with cup (race). Cone and
cup sold as set only............. 2
11601 Shaft-main drive, power unit. Incl.
integral worm, plus two pressed-
on cone roller bearings, two
bearing cups and two shoulder
washers................................ 1
9617 Seal-oil, drive shaft, rear........ 1
9517 Retaining Ring-(snap ring), internal.1
PINION SHAR ASSEMBLY
9309 Pin-roll (spirol), 1/4 X 2"........... 2
1060A Plug-retaining, pinion bearing (incl.
Ref. No. 52)........................... 2
9604 0-Ring-retaining plug............... 2
1132-1 Shim-retaining plug, 1-1/64“ Inner
dia., .033" thick (on right side
only one #1132-1 shim is also
used between bearing and washer.
Ref. No.’s 54 & 55)............. As
Req'd
(continued on page 55)
53