Troubleshooting, Warranty, Call us first – Ryobi CS30 RY30923 User Manual

Page 12

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

SOLUTION

PROBLEM

POSSIBLE CAUSE

Engine will not start

1. No spark.

2. No fuel.

3. Engine is flooded.

1. Check spark. Remove spark plug. Reattach

the spark plug cap and lay spark plug on metal

cylinder. Pull the rope and watch for spark at
spark plug tip. If there is no spark, repeat test

with a new spark plug.

2. Push primer bulb until bulb is full of fuel. If bulb

does not fill, primary fuel delivery system is

blocked. Contact a service dealer. If primer
bulb fills, engine may be flooded, proceed to

next item.

3. Set the start lever to the START position. Squeeze

the trigger and pull the rope repeatedly until the

engine starts and runs.

NOTE: Depending on the severity of the flooding,
this may require numerous pulls of the rope. See

Figure 23.

Engine does not reach full
speed and emits excessive
smoke

1. Incorrect oil/fuel mixture.

2. Air filter is dirty.

3. Spark arrestor screen is dirty.
4. Spark plug fouled.

1. Use fresh fuel and the correct 2-cycle oil mix.

(50:1).

2. Clean airfilter. Refer to Replacing and Cleaning

Air Filter earlier in this manual.

3. Contact a servicing dealer.

4. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

Engine starts, runs, and ac­
celerates but will not idle

1. Idle speed screw on carburetor

needs adjustment.

1. Turn idle speed screw clockwise to increase idle

speed. See Figure 31.

String will not advance

1. String is welded to itself.
2. Not enough string on spool.

3. String is worn too short.

4. String is tangled on spool.

5. Engine speed is too slow.

1. Lubricate string with silicone spray.
2. Install more string. Refer to String Replacement

earlier in this manual.

3. Pull strings while alternately pressing down on:

and releasing spool retainer.

4. Remove string from spool and rewind. Refer to

String Replacement earlier in this manual.

5. Advance string at full throttle.

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Spool retainer hard to turn

1. Screw threads are dirty or

damaged.

1. Clean threads and lubricate with grease - if no

improvement, replace the spool retainer.

Grass

wraps

around

driveshaft

housing

and

string head

1. Cutting tall grass at ground

level.

2. Operating trimmer at part

throttle.

1. Cut tall grass from the top down to prevent

wrapping.

2. Operate trimmer at full throttle.

WARRANTY

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

>

Emissions Parts Inspect Before

Clean Every

Replace

Clean Every

Replace Every

Each Use

5 Hours

Every 25 Hours

25 Hours

50 Hours

or Yearly

or Yearly

CATALYTIC MUFFLER ASSEMBLY.......................................................................................................................X
AIR FILTER ASSY

includes:

Filter................................................................... X.............................. X

SPARK SCREEN...................................................................................................................... X

CARBURETOR ASSY

includes:

Fleat Dam

Gaskets

FUEL TANK ASSY

includes:

Fuel Lines.........................X

Fuel Cap...........................X

Fuel Filter

IGNITION ASSY

includes:

Spark Plug........................................................................................... X

ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

22

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi® Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

23

Advertising
This manual is related to the following products: