English, A© k – Vitek VT-4086 SR User Manual

Page 10

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

ENGLISH

Audio Setup Page
The setup structure is as below:

properly and try out the sound field balance.

Warning: Although the white noise is in lowvolume, please make sure

system master volume is adjusted to a low level before active the test

tone function to avoid any potential damage.

-- AUDIOSETUP P AGE--

Speaker Setup
SPDIE Setup

DIoby Digital Setup

Channel Delay

Equalizer

3D Processing

Dialog

When DOWNMIXoption is setto LT/RT or STEREO mode, adjustingthe
value ofthis item to control the volume of the player. Preset valueisO.

SPDIFOutput

This function is for user to select right SPDIF

Digital Audio output for external Audio decoder.

Press arrow buttons to select, and press PLAY/PAUSE button to confirm. The setup menu structure is as below:

Speaker setup page

a

© K

--Speaker Setup Page--

Downmlx

STR

Lt/RT

Stereo

VSURR

Off

Front Speaker

LRG

Large

Small

Center Speaker

SML

Large

Small
Off

Rear Speaker

SML

Large

Small
Off

Subwoofer

On

On
Off

Test Tone

Off

On
Off

Dialog

00

Downmlx

LT/RT: Selectthis option when the DVD player is connectto external

amplifier with Pro-Logic decoding function.
STEREO: Select this option when you want to use onlythe front-left
& front-right speakers with normal sound effect.
Surround: Select this option when you want to use onlythe front-left
& front-right speakers with Virtual Surround Sound effect
Off: Default setting, to output full decoded 5.1- channel surround
sound.

Central speaker

Small: Default setting. To use the original satellite centre speaker.

Large: Select this option onlywhen the DVD player is connected to

external amplifier with full range centre speaker.

Off: Select thisoptiononlyif there is no centre speaker connected.

Rearspeaker

Small: Default setting. To use the original satellite rear speakers.

Large: Select this option onlywhen the DVD player is connected to

external amplifier with full range rear speakers.

Off: Select thisoptiononlyif there is no rear speaker connected.

Subwoofer

On: Default setting. To usetheoriginal activesubwooferspeaker.

Off: Select this option only when the DVD player is connected to
external amplifier with full range front speakers and no subwoofer
speaker connected.

Test Tone

When test tone function is activated, the player will generate white noise

channel by channel for user to test, if the 5 satellite speakers positioned

a

SPDIF Setup Page

SPDIFOutput RAW

SPDIF/Off
SPDIF/RAW
SPDIF/PCM

PCM Channel L/R

SPDIF L/R
SPDIF LS/RS
SPDIF C/LFE

LPCM Out 48K

48K

96K

SPDIF output

There are three SPDIF output modes: SPDIF/OFF, SPDIF/RAW, SPDIF/

PCM.

SPDIF/OFF: Close up coaxial output.

SPDIF/RAW: To output not decoded raw data for all audio source.

SPDIF/PCM: To output decoded digital PCM data for all audio

sources.

PCM Channel
In the Manual SPDIF output setting mode, setthe SPDIF outputfor each

of the different source.

LPCM out

48 K: To selectthe highest SPDIF/PCM output sampling rateat48KHz.

Higher sampling rate audio source will be down sampled to 48 KHz or

lower rate.

96 K: To selectthe highest SPDIF/PCM output sampling rate at96KHz.

Down sampling function will not be implemented.
NOTE: Not all AV Receiver can support 96 KHz sampling rate.

Dolby Digital Setup

Front Speaker

Large: Default setting, Selectthis option onlywhen the DVD player is

connected to external amplifier with full range front speakers.

Small: To usethe original satellitefront speakers.

a

-Dolby Digital Setup-

Dual Mono STR

Stereo

L-Mono
R-Mono
Mix-Mono

Dynamic

Dual Mono

Stereo: The player will output Left channel and Right channel audio.

L-mono: The player will output left channel audio only from the 2 front

channels.

R-mono: The player will output rightchannel audio onlyfrom the 2 front

channels.

Mix-mono: The player will output the average signal ofthe mixed Left

channel and Right channel audio from the 2 front channels.

Dynamic

This isto setup the Dynamic compression ration. Press rightarrow but­
ton to enter the setup column; adjust the rate ofthe dynamic range by

pressing up or down arrow button. Default setting is off.

m

Advertising