Denon AVR-2801 - Manual (Page 28)

ENGLISH
28
Learning function
• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-2801/981’s
remote control to “learn” the codes from the component’s original remote control.
• The buttons that can be “learned” are the CD, DECK and CDR/MD system buttons (see page 24) and the DVD, VDP, VCR and TV system
buttons (see page 27). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block
buttons can also be “learned”.)
1 Press the USE/LEARN selector button with the tip of a pen
etc., to set the learn mode. Both the START and LEARNED/TX
indicators flash.
This unit’s remote
control unit
Flashes
2 Set the program switch to the side to be learned.
Set to the AUDIO side for the CD, tape deck or CDR/MD
position, to the VIDEO side for the DVD, VDP, VCR or TV
position.
AVR/AVC VIDEO
AUDIO
3 Set the program switch to the position to be learned.
4 Set the remote control units so they are facing each other,
then press the button to be learned on this unit’s remote
control unit.
The indicator stops flashing and the START LED lights.
The learnable buttons are the buttons which can be operated
with the DENON system codes for the CD player, tape deck,
CD recorder, MD recorder, the buttons which can be operated
with the preset memory for the DVD, VCR, VDP and TV. For
the TV only, however, the buttons in the section indicated “A”
on the diagram above can also be “learned”. Use these to
“learn” TV channels.
DVD TV
VDP VCR
CD
CDR/MD DECK
This unit’s remote
control unit
Transmitting windows Other remote
control unit
Approx.
5 cm
DVD
SPEAKER
TUNING
BAND TITLE MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS SURROUND DIRECT
DSP SIMULATION 5CH STEREO STEREO
INPUT MODE ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD CDR/MD DECK
SYSTEM SETUP SURROUND PARAMETER
CH SELECT
SELECT
1 2 3
4
SET
A / B
CALL OFF
ENTER
ON / SOURCE
5 6
7 8 9
+10 0
A
2
4
3
B
1,8
CDR / TAPE
5 Check that the START LED is lit, then press the button to be
“learned” on the other remote control unit.
6 Once the START LED turns off and the LEARNED/TX LED
lights, release the button on the other remote control unit.
7 To “learn” other buttons, repeat steps 2 to 6.
8 Once the learning operation is completed, press the
USE/LEARN selector button again.
The two LEDs stop flashing and the learning mode is
cancelled.
This unit’s remote
control unit
Other remote
control unit
The two LEDs start
flashing again.
Light
Light
NOTES:
• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.
• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s)
is released.
• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes
cannot be stored in RC-881.
• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just
attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 31.)
Check that the stored
codes work properly.