ADLINK cExpress-BL - Manual (Page 18)

Page 18 cExpress-BL
3.3.4 Gigabit Ethernet
Gigabit Ethernet Pin # Description I/O PU/PD Comment
GBE0_MDI0+
GBE0_MDI0-
GBE0_MDI1+
GBE0_MDI1-
GBE0_MDI2+
GBE0_MDI2-
GBE0_MDI3+
GBE0_MDI3- A13
A12
A10
A9
A7
A6
A3
A2 Gigabit Ethernet Controller 0: Media Dependent Interface Differential Pairs
0, 1, 2, 3. The MDI can operate in 1000, 100, and 10Mbit/sec modes.
Some pairs are unused in some modes according to the following:
1000BASE-T 100BASE-TX 10BASE-T
MDI[0]+/- B1_DA+/- TX+/- TX+/-
MDI[1]+/- B1_DB+/- RX+/- RX+/-
MDI[2]+/- B1_DC+/-
MDI[3]+/- B1_DD+/-
I/O Analog Twisted pair
signals for
external
transformer.
GBE0_ACT# B2 Gigabit Ethernet Controller 0 activity indicator, active low. O 3.3VSB PU 10k
3.3VSB
GBE0_LINK# A8 Gigabit Ethernet Controller 0 link indicator, active low. O 3.3VSB
GBE0_LINK100# A4 Gigabit Ethernet Controller 0 100Mbit/sec link indicator, active low. O 3.3VSB
GBE0_LINK1000# A5 Gigabit Ethernet Controller 0 1000Mbit/sec link indicator, active low. O 3.3VSB
GBE0_CTREF A14 Reference voltage for Carrier Board Ethernet channel 1 and 2 magnetics
center tap. The reference voltage is determined by the requirements of the
Module PHY and may be as low as 0V and as high as 3.3V. The reference
voltage output shall be current limited on the Module. In the case in which
the reference is shorted to ground, the current shall be 250 mA or less. GND min
3.3V max No support on
this product
3.3.5 Serial ATA
Signal Pin # Description I/O PU/PD Comment
SATA0_TX+
SATA0_TX- A16
A17 Serial ATA channel 0, Transmit Output
differential pair. O SATA AC coupled on Module
SATA0_RX+
SATA0_RX- A19
A20 Serial ATA channel 0, Receive Input
differential pair. I SATA AC coupled on Module
SATA1_TX+
SATA1_TX- B16
B17 Serial ATA channel 1, Transmit Output
differential pair. O SATA AC coupled on Module
SATA1_RX+
SATA1_RX- B19
B20 Serial ATA channel 1, Receive Input
differential pair. I SATA AC coupled on Module
SATA2_TX+
SATA2_TX- A22
A23 Serial ATA channel 2, Transmit Output
differential pair. O SATA AC coupled on Module
SATA2_RX+
SATA2_RX- A25
A26 Serial ATA channel 2, Receive Input
differential pair. I SATA AC coupled on Module
SATA3_TX+
SATA3_TX- B22
B23 Serial ATA channel 3, Transmit Output
differential pair. O SATA AC coupled on Module
SATA3_RX+
SATA3_RX- B25
B26 Serial ATA channel 3, Receive Input
differential pair. I SATA AC coupled on Module
(S)ATA_ACT# A28 ATA (parallel and serial) or SAS activity
indicator, active low. O 3.3V