Weston #5 Deluxe Electric Meat Grinder - Manual (Page 8)

-8- -13-
NOTE: The Tomato & Fruit Strainer Attachment
cannot be used with meat products.
NOTE: Follow the “Food Safety Guidelines” in this
manual and as outlined by the U.S. Food and Drug
Administration (FDA) whenever using this appliance.
Keep meat/food refrigerated and covered. Do not
let meat/food sit out any longer than is necessary for
processing.
1. Cut large fruits and vegetables into quarters and
small fruits and vegetables in half.
IMPORTANT: Remove pits, stems, shells
and seeds before placing fruits or vegetables
into the Tomato & Fruit Strainer to avoid
damaging the Screen.
2. Place the fruits/vegetables in the Tray. Do not
overfill the Tray. DO NOT operate the Grinder without
the Tray in place.
3. Place a bowl under the Plastic Chute to collect juice and pulp. Place a bowl
under the Screen outlet to collect skin and seeds.
4. Feed the fruits/vegetables into the Grinder Head. Use the Stomper to push the
fruits/vegetables into the Grinder Head. Never use your fingers!
11. When straining is complete, turn the Motor Unit “off” and disconnect it from the
electrical outlet.
HELPFUL HINTS:
A. Rerun the skin and seeds through the Food Strainer to extract any
leftover pulp & juice. Repeat as necessary.
B. Use a rubber spatula to scrape pulp from the Screen into the Chute.
USING THE TOMATO & FRUIT
STRAINER
Not included with all grinders.
STUFFER ASSEMBLY
1. Place the Plastic Washer then the Bushing Set onto the end of the Auger opposite
the Pin (figure 3).
2. Carefully insert the Auger into the Grinder Head.
3. Place the Knife onto the square portion of the Auger Pin. The cutting edges of the
Knife should face outward (figure 4).
4. Place the Coarse Grinder Plate onto the round portion of the Auger Pin. Align the
tabs on the Grinder Plate with the notches in the Grinder Head.
5. Insert the Stuffing Funnel through the Front Ring Nut (figure 3).
6. Screw the Front Ring Nut/Stuffing Funnel assembly onto the Grinder Head until
firmly tight. DO NOT over-tighten the Front Ring Nut to avoid damaging the Grinder
during operation.
7. Loosen the Head Locking Knob on the side of the Motor Unit.
8. Install the Grinder Head onto the Motor Unit (figure 3).
9. Tighten the Head Locking Knob to secure the Grinder Head.
10. Install the Tray onto the Grinder Head. Press the Tray down until fully seated (figure 3).
Figure 3
Front
Ring
Nut
Auger
Plastic
Washer
Grinder
Head
Motor
Unit
Tray
Stomper
Head
Locking
Knob
Knife
with
cutting
edges
facing
outward.
Figure 4
Grinding
Plate
Stuffing
Funnel
8. Install and firmly tighten the Front Ring
Nut (make sure the tabs remain aligned with the
notches). DO NOT over-tighten the Front Ring Nut
to avoid damaging the Grinder during operation.
9. Loosen the Head Locking Knob on the side
of the Motor Unit.
10. Insert the Screen end of the fully-assembled
Grinder Head through the outlet end of the Plastic
Chute (figure 9).
11. Install the
Grinder Head onto the Motor Unit.
12. Tighten the Head Locking Knob to secure the
Head in place.
13. Install the
Tray onto the Grinder Head. Press the Tray down until fully seated (figure 9).
Figure 9
Reverse
Button
Power
Switch
Auger
Pin
Bushing
Set
WARNING! Before cleaning, assembling or disassembling the Grinder, make sure
it is turned “off” and disconnected from the power source. Test to make sure there is
no power to the Grinder by switching the Motor Unit “on” and “off.”
Follow all of the Safety Rules
and Warnings in this manual
whenever using this appliance.
Never leave this
appliance unattended.
Disconnect from power supply
when not in use.
WARNING!
Keep fingers, hands,
other body parts and
foreign objects away
from the inlet during
operation!
Only use the provided
stomper to push food into
the appliance.
Keep children away!