XAIRCRAFT X650 Value - Manual (Page 5)

Before Flight
DISCLAIMER OF LIABILITY INSPECTIONS BEFORE FLIGHT
1. Using XAirctaft products within the limits permitted by local laws and PLEASE PAY ATTENTION TO THE AGING AND WORN PARTS, AND FLY WHEN THEY ALL
regulations. XAircraft is not responsible for any illegal activities. WORK WELL. PLEASE DO CHECK EVERY ASSEMBLY CAREFULLY BEFORE FLIGHT,
2. The X650 Value is an aeromodelling product only. Please strictly follow the especially lapses in these parts will easily cause DANGER.
aeromodelling safe function rules, XAircraft does not hold responsible for 1. Check that the propellers are secured properly.
any control over its operation or usage. 2. Check that the receiver is receiving a stable signal.
3. Model aircraft are not toys! Fly under professional guidance and strictly 3. Check that the battery is secured tightly and the battery is fully charged.
follow instruction rules in this document. XAircraft is not responsible for 4. Check that the receiver is attached correctly.
consequences caused by improper install, wrong setting or operation. 5. Check the antenna is assembled tightly enough.
6. Check that the brushless motor and brushless ESC are secured to the
SAFETY CAUTIONS airframe.
X650 Value gives users an enjoyable fly experience but is potentially dangerous at the Before flight, please assemble receiver or connect ESC to FC as XAircraft factory
same time. The blades rotate up to 4000RPM which can cause serious injuries or defaults, if not, please DO CHECK the operations of Remote Control channels and
property damage. Safety awareness should be firmly followed by all users regardless consistence of motor reactions.
of flying experience.
1. Familiarize yourself with fly environment and any obstacles. Identify any FLIGHT CONTROL INSTRUCTION
potential hazards such as power lines, cars, people, etc. 1. Start: Set the throttle stick to the lowest then turn on the transmitter.
2. Do not fly the aircraft when fatigued, drunk or your mental state has been Connect the flight battery then slowly apply the throttle until all motors
compromised which may cause an accident. begin to run.
3. Stay away from wet areas. Do not fly in the rain or wet environments which 2. Stop: Move the throttle stick to the minimum. All motors should stop to
can cause device failure and probably lead to danger. Do not fly at night or work in about one second. First cut off the X650 Value then the RC powers
in windy conditions. off.
4. Stay away from any fire resulting in damage of the electronic parts or others 3. Any emergency occurs when taking off or landing, please move the throttle
such as the flight battery. stick to the lowest position immediately to keep safe.
5. Do not fly alone during your preliminary flights. If you need help, please 4. Flight control to the front, back, left and right is similar to the traditional RC
enlist the aid of an experienced pilot before flying for the first time. helicopters but each motion is controlled by a separate channel. Do not use
6. Prepare rescue tools such as cell phones or other communication devices any channel mixing in your RC transmitter such as v-tail or swashplate
which should you need to call for help. mixing etc.
7. Please fly under safe take-off weight, do not overload the aircraft which can
lead to danger.
START TO FLY
8. Ensure all the equipment operates correctly before flight and that there is Power ON/OFF Operations: Before plugging in the quad you have to turn on the RC
no transmitter interference or conflicts. and set the throttle stick to the lowest position. When powering off, you have to cut
9. Do not touch any moving or powered parts. Do not try to catch the off the aircraft first then the RC powers off. Disorder in the on and off procedure will
quadcopter which has rotating motors or blades for example. Keep loose cause an accident.
clothing away from moving parts as they may get caught and could cause 1. Place the aircraft on the ground. Put the throttle stick to the lowest position
physical harm. then turn on the transmitter.
10. Always throttle down to minimum before fly. 2. Connect the battery to the ESC board.
11. Remove the propellers when testing the remote device or motors operation. 3. Start the Quad by applying power slowly with the throttle stick. When all the
Attach the propellers after you have tested that everything is working good motors rotate at a slow speed you can move the stick to check the X650
to prevent an accident. Value actions according to your operation.
12. Assemble the aircraft with accessories XAircraft provides. XAircraft is not 4. If you can not calibrate the tilt on one side during your flight, please
responsible for any consequence resulted from assembly with other connect X650 Value to the PC and use XAircraft configuration software to do
accessories or modifications. the calibration.
3 www.xaircraft.com