Desa CF26PR - Manual (Page 17)

17 105442
OWNER’S MANUAL
For more information, visit www.desatech.com
OPERATING
HEATER
Continued
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
2a. Set selector switch in the OFF position
2b.
If Using Optional Hand-Held Re-
mote:
Set selector switch in the OFF
position to keep from draining battery.
Shutting Off Burner Only (pilot
stays lit)
You may shut off the burner and keep the
pilot lit by doing one of the following:
1. Turn control knob clockwise
to the PILOT position.
2. Use remote control manual OFF button.
3. Set selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
Thermostat Control Operation
(Optional CGHRCT Series Only) The
thermostat control setting on the remote
control unit can be set to any comfort
level between HI and LO. The burner will
turn on and off automatically to maintain
the comfort level you select. The ideal
comfort setting will vary by household
depending upon the amount of space to
be heated, the output of the central heat-
ing system, etc.
1. Follow steps 1 through 6 under Light-
ing Instructions, page 16.
2. Depress control knob and light pilot
with match.
3. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow steps 9 through 11, column 1.
OPTIONAL REMOTE
OPERATION
NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See
Lighting
Instructions on page 16 and 17.
Note: All remote control accessories must
be purchased separately (see Accessories,
page 28). Follow instructions included
with the remote control.
1. After lighting, let pilot flame burn for
about one minute. Turn control knob
to ON position. Adjust flame adjust-
ment knob anywhere between HI
and LO. Slide the selector switch to
the REMOTE position.
NOTE: The
burner may light if hand-held remote
ON button was on when selector
switch was last turned off. You can
now turn the burner on and off with
the hand-held remote control unit.
IMPORTANT: Do not leave the selector
switch in the REMOTE position when the
pilot is not lit. This will drain the battery.
IMPORTANT: Be sure to press the ON/
OFF buttons on the hand-held remote
control unit for up to 3 seconds to assure
proper operation.
CGHRC Operation:
2a. Press the ON/OFF button to turn the
burner on and off. When turning
burner off, the pilot will remain lit.
Note: If pilot does not stay lit, con-
tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure.
8. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
• If control knob does not pop out when
released, contact a qualified service
person or gas supplier for repairs.
Note: If pilot goes out, repeat steps
4 through 8.
9. Slightly push in and turn control
knob counterclockwise
to the
ON position.
10. Wait one minute and switch selector
switch to the ON position to light
burner.
11. Set flame adjustment knob to any
level between HI and LO.
CAUTION: Do not try to adjust
heating levels by using the equip-
ment shutoff valve.
WARNING: Make sure the
selector switch is in the OFF po-
sition when you are away from
home for long periods of time.
Heater will come on automati-
cally with selector switch in the
ON position.
Figure 34 - Pilot
Ignitor
Electrode
Pilot Burner
Continued
Figure 35 - Setting the Selector Switch, Control Knob, and Flame
Adjustment Knob for Remote Operation
Selector Switch in Remote Position (Optional
Remote Control)
ON
OFF
REMOTE O FF
PILO
T
O
N
L O
I H
Control Knob in
On Position
Flame Adjustment Knob