Sun valley stove company, Cast iron stove and burner system, Troubleshooting venting problems – Desa MSRBVN User Manual

Page 12: Stove and b-vent burner system installation

Advertising
background image

12

CAST IRON STOVE AND BURNER SYSTEM

106706

SUN VALLEY STOVE COMPANY

For more information, visit www.desatech.com

TROUBLESHOOTING
VENTING
PROBLEMS

Most venting problems are caused by incor-
rect vent sizing, improper installation, or
inadequate air supply. A preliminary check
for a field problem might include:

• Using a draft meter to determine if

venting system draft meets
manufacturer’s specifications

• Checking the vent sizing according to

manufacturer’s specifications, appliance
input, and venting configuration

• Examining the entire venting system for

faults such as disconnected joints for
damaged vent sections

• Making sure vent and air openings are

not obstructed

If these procedures do not reveal the source of
the problem, troubleshooting may include
attention to common venting problems.

FLUE GAS SPILLAGE

Spillage occurs when flue gases cannot exit
the vent system and back up into the dwell-
ing. A primary symptom of appliances
equipped with a Vent Safety Shutoff System
(flue spill switch) is unexplained appliance
shutoffs. Other symptoms of flue gas spillage
at the draft hood include condensation on
walls and windows and/or noticeable odors.
Spillage may also result in the release of
carbon monoxide, a colorless, odorless, highly
toxic gas. A simple spillage test can be con-
ducted if spillage is suspected. See Checking
Gas Connection
, pages 14 and 15.

CAUSES OF SPILLAGE AND
CORRECTIVE ACTION

Incorrect Vent Sizing

If the vent is too small or too short, spillage
may occur. If the vent is too large, excessive
dilution air may cool flue gases and reduce
draft, causing spillage. The vent cap size
should also be checked. Check
manufacturer’s instructions, appliance in-
put rating, and appropriate sizing tables.

Venting Condition

Loose joints can affect draft and cause spill-
age. “Mashed” vent sections and damaged
vent caps can restrict flow and cause spill-
age. Examine and replace as needed.

Obstructions

Small animals or birds may get into and block
the vent or draft hood outlet. Dust, lint, and
foreign objects may obstruct air inlets. Re-
move obstructions and clean openings.

Lateral Run

Lengthy horizontal or non-vertical runs cause
resistance to flow and may reduce draft
enough to cause spillage. The pitch of lateral
runs can also be a problem; lateral runs
should be pitched 1/4" rise per foot of hori-
zontal run from the appliance to the vent.

Elbows

Too many elbows cause excessive restric-
tion of flow and may result in spillage.
Usually, two 90º turns can be tolerated in a
properly sized venting system. More than
two may cause problems and necessitate
changing the system.

Negative Pressure in the
Dwelling

An extremely tight house may not supply
adequate combustion and venting air. Use
of mechanical exhaust such as a dryer vent
or range vent may worsen the problem. An
air exchange system must be installed in the
dwelling to correct this problem.

Flue Gas Cooling

Venting exposed to extremely cold tem-
peratures or venting of single wall construc-
tion loses heat needed to maintain draft;
massive masonry chimneys absorb needed
heat. If the flue gases cool excessively, draft
is reduced and spillage may result. Use
proper materials, insulate and protect prop-
erly, reline when necessary.

Down Drafts

In certain wind conditions and in certain
relationships with nearby structures and
objects, high pressure conditions may affect
draft negatively. Relocate the vent cap, raise
its height, or use an approved high wind cap.

STOVE AND B-VENT
BURNER SYSTEM
INSTALLATION

INSTALLING GAS PIPING TO
FIREPLACE LOCATION

WARNING: A qualified in-

staller or service person must
connect burner system to gas
supply. Follow all local codes.

CAUTION: For propane/LP

units, never connect heater di-
rectly to the propane/LP supply.
This heater requires an external
regulator (not supplied). Install the
external regulator between the
heater and propane/LP supply.

CHECK GAS TYPE

Use proper gas type for the burner system
unit you are installing. If you have conflict-
ing gas types, do not install burner system.
See dealer where you purchased the burner
system for proper system according to your
gas type.

NOTICE: This heater is intended
for use as supplemental heat. Use
this heater along with your pri-
mary heating system. Do not in-
stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’s circulating blower while
using heater. This will help circu-
late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.

Advertising
This manual is related to the following products: