DFI DL631-C226 - Manual (Page 9)

www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
1 5
4 8
12 24
13
COM2
COM1
LAN 1
USB 0-1
USB 3.0
LAN 2
USB 4-5
USB 3.0
Line-in
Line-out
Mic-in
+12V
Power
Intel
C226
Standby
Power LED
1
1
1
1
1 1
1 1
1
SATA DOM Power
Select (JP15)
1
USB 2-3/6-7
Power Select (JP8)
System Fan 1 1
6
5 2
1
SMBus
1
2
9
10
1
2
9
10 USB 6-7 USB 2-3
Nuvoton
NCT6106D
LPC 12
1 11
2
System Fan 2
1
1
2 5
6 1
2 5
6
1
1
USB 0-1 Power
Select (JP5)
Realtek
ALC886
2
9
10
1
1
S/PDIF
Front
Audio
DDR3_1 DDR3_3
Chassis
Intrusion1
ITE
IT8892E
1 1 1
PCI 1
PCI 2
PCI 3
PCIe x16 (PCIe 1, x16 signal)
1 2
5 6
1 2
5 6
USB 4-5 Power
Select (JP6)
(JP2)
USB 2.0
SATA 3.0
Socket LGA1150
DDR3_4 DDR3_2
PCIe x4 (PCIe 2)
PCIe x4 (PCIe 3, x1 signal)
(JP12) (JP13) (JP7)
Front
Panel
1 2
11 12
RSVD
RESET-SW
HDD-LED
RSVD
PWR-LED
ATX-SW
ASMedia
ASM1442
ASMedia
ASM1442
Intel
WGI217LM
Intel
WGI210AT
1
1
(JP11)
ISL95820 (JP1)
(JP14)
PCIe x16 (PCIe 4)
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select
COM1 RS232/422/485
Select
COM2 RS232/422/485
Select
COM1 RS232/Power
Select
COM2 RS232/Power
Select
(JP2)
(JP11)
(JP3)
(JP14)
(JP4)
(JP3) (JP4)
PS/2 KB/MS
USB 8-9
USB 2.0
DIO Power Select
(JP13)
DIO 11/13/15/17
Output State (JP7)
DIO 3/5/7/9
Output State (JP12)
DVI-I
HDMI
Buzzer
CPU Fan
1
Battery
SPI Flash
BIOS
Power-on
Select (JP10)
Clear CMOS
Data (JP9)
SATA 0
SATA 1
SATA 3 SATA 2
SATA 4 SATA 5
1
ATX
Power
DIO
COM5 COM6
COM4
COM3
1
2
19 Note:
SATA5 supports SATA DOM.
1
2 10
9 1
2 10
9
1 2
10 9
1 2
10 9
System Memory
Standby
Power LED
Features
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lit red, it indicates that there is power on the system
board. Power-off the PC then unplug the power cord prior to installing any devices.
Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
DDR3-2
DDR3-1
DDR3-4
DDR3-3
Channel A
Channel B
• The four DIMM sockets are divided into 2 channels:
Channel A - DDR3_1 and DDR3_2
Channel B - DDR3_3 and DDR3_4
• Supports DDR3 1333/1600MHz
• Supports dual channel memory interface
• Supports up to 32GB system memory