DFI HD636-H81CS - Manual (Page 9)

9
Chapter 2 Hardware Installation
Chapter 2
www.dfi .com
Chapter 2 - Hardware Installation
Board Layout
System Memory
Features
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lights red, it indicates that there is power on the sys-
tem board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
DDR3-1
• One 240-pin DDR3 DIMM socket
• Supports DDR3 1333/1600MHz
• Supports up to 8GB system memory
• Supports single channel memory interface
Buzzer
SATA DOM
Power Select
(JP11)
PS/2 MS
PS/2 KB
Battery
1
1
1
SPI Flash BIOS
Standby
Power LED
1
1
1
1
1 1
1
1
System
Fan 1
S/PDIF 1
+12V
Power
1 5
4 8
1 1 1
2
9
10
1
Front Audio
LAN 1
USB 0-1
USB 3.0
LAN 2
USB 4-5
USB 2.0
Line-in
Line-out
Mic-in
DIO 1
2 19
PCIe 2 (PCIe x4)
PCIe 3 (PCIe x4)
Socket LGA1150
1
2
25
26
Parallel
CPU Fan
1 2
10 9
1 2
10 9
COM 6 COM 5
1 2
10 9
1 2
10 9
COM 4 COM 3
12 24
ATX
Power
1 13
1
2 10
9 1
2 10
9
COM 7 COM 8
1 2
Front Panel
11 12
1
2
11
12
LPC Debug
DDR3_1
Nuvoton
NCT6106D
System
Fan 2
1
Power-on
Select (JP10)
Clear CMOS
Data (JP9)
1
2
9
10
USB 8-9
PS/2 KB/MS Power
Select (JP1)
USB 4-5
Power Select
(JP6)
USB 0-1
Power Select
(JP5)
Intel
H81
1
2
9
10
USB
10-11 USB 2
(JP7) (JP12) (JP13)
DIO Power Select
(JP13)
DIO 11/13/15/17
Output State (JP7)
DIO 3/5/7/9
Output State (JP12)
PCIe 1 (PCIe x16)
2
1
6
5
2
1
6
5
2
1
6
5
2
1
6
5
Nuvoton
NCT5104D
ISL95820
2
1 5
SMBus
1 4
PCI 1
PCI 2
PCI 3
PCI 4
COM 1
HDMI
COM 2
VGA
Chassis
Intrusion
SATA 0
1
SATA 1
1
SATA 4
1
SATA 5
1
USB 8-9/10-11
Power
Select (JP4)
USB 2 Power
Select (JP8)
(JP17)(JP18) (JP2)
COM 8 RS232/Power
Select (JP14)
COM 8 RS232/422/485
Select (JP2)/(JP17)/(JP18)
Note:
SATA 0 supports SATA DOM.
SATA 3.0
SATA 2.0
USB 2.0
USB 2.0
Realtek
ALC888
ASMedia
ASM1442
ASMedia
ASM1182
Intel
WG82574L
Intel
WG82574L
ITE
IT8892E
Standby
Power LED
• The vertical USB (USB 2) co-lays with a USB pin header(USB 2-3) on the system board.