Fenix ECOFLEX TAC - Manual (Page 3)

3
Caution (EN)
Caution very hot surface.
CAUTION: Portions of this product may become hot and cause burns. Pay particular attention to the
presence of children and vulnerable people.
- Keep away from this unit child under 3 years unless they are under continuous surveillance.
- This device should not be used by unsupervised children under 14 years old, by people with physical, sensory or mental
capabilities and by persons with lack of experience or knowledge, unless they can benefit through a person responsible for
their safety of prior instructions.
- Children less than 14 years old should not play, adjust, clean or perform maintenance on the unit.
- This device must be plugged or connected according to the rules and standards applicable by an authorized person.
- The instruction book of this product is available by contacting the after-sales service with the number indicate on the
warranty part included in this manual service.
- If the power cable is damaged, it must be replaced by the manufacturer, its after sales service or similarly qualified persons
in order to avoid any danger.
Caution: to avoid overheating and for safety reasons, do not cover the panel heater.
Devices with this symbol should not be disposed with household waste but must be collected separately and
recycled. The collection and recycling of end of life must be made according to the provisions and local ordinances
(DEEE 2002/96/CE).
The installation of the device in high altitude causes an increase of the temperature air outlet (about 10 ° C per 1000
m elevation).
In case of mobile utilisation of the device (see applicable models below):
- Do not use this heater near a bathtub, a shower or a pool.
- Do not use this heater in small areas when they are occupied by people unable to leave the room by themselves unless if a
constant supervision is provided.
1. Installation
1.1 Where to install your heater?
- This equipment was designed to be installed in a residence. Please ask your distributor before using it for any other
purpose.
- The panel heater should be installed according to normal trade practice and incompliance with legislation in the relevant
country (NFC 15-100 for France).
- The equipment is class 2 and is protected against splashed water IP 24. The device can be installed in volume 2 of a
bathroom (Figure ❶). It’s forbidden to install the device in the volume 1. The device is to be installed so that switches and
other controls cannot be touched by a person in the bath or shower.
- Comply with the minimum clearance distances for positioning of the panel (Figure ❷).
- The wall bracket allows keeping a free space behind the device to not disturb its regulation. The distance between the unit
and the wall should not be obstructed.
1.2 Do not install the panel heater
- In a draught that might affect adjustment (for example, under a central mechanical ventilation unit etc...). Under a fixed
power socket (Figure ❸) or near curtains or other combustible materials.
- In a non-conform position.
- The air outlet grid and the control unit is visible in the upper part of the device. It is forbidden to install a vertical unit
horizontally and vice versa (Figure ❹).
1.3 How to install the panel heater?
WARNING: Devices without plug can not be used in mobile version
1.3.1 Preparation
- The wall mounted installation concern all Mechanical devices and Electronic devices.
a.
Release the appliance’s hook-on bracket (Figure ❺)
- We recommend that you place the panel heater flat, face down. Have a straight head screwdriver to hand and lift the tab
taking care not deform. While holding the tab rose, push the locking bracket to the bottom of the unit to release the upper
hooks. Rotate the attachment tab around the lower hooks and remove the attachment tab.
b. Fix the hook-on bracket (Figure ❻)
- Place the bracket on the ground and against the wall and mark the drilling points A. These give the position of the bottom
fasteners. Replace the brackets in alignment with the drilling point A to locate drilling points B. These give the position of
the upper fasteners. In case of special support, use proper anchors. Position and screw the wall brackets.
1.3.2 Electrical connexion
- The appliance should have a 230 / 50Hz power supply. The panel heater must be connected to the mains by a 2-wire cable
for Mechanical Device or 3-wire cable for Electronic Device (Brown= Phase, Blue = Neutral, Black = Pilot wire) by means of
a connexion box. In humid areas such as bathrooms and kitchens the power socket must be installed at least 25 cm above
the floor. The installation should be fitted with a double pole break device with a break of at least 3 mm.
- Connection to earth is prohibited / Do not connect the pilot wire (black) to earth. If a driver or driven device is
protected by a 30mA differential (for example for bathroom) it is necessary to protect the power supply of the pilot wire on
that differential.