Flowserve DS - Manual (Page 34)

DS USER INSTRUCTIONS ENGLISH 71576283 - 02/13
02
Page 34 of 36 flowserve.com
8.2 Sectional drawing parts list
Item Designation
1110 Pump casing
1221 Casing cover
1500-01 Wear ring
1500-02 Wear ring
2110 Shaft
2250 Impeller
2450-01 Shaft sleeve
2450-02 Shaft sleeve
2540-01 Deflector
2540-02 Deflector
2900 Washer
2905 Washer
3011 Radial ball bearing
3012 Radial roller bearing
3126 Shim
3134 Support foot
3200 Bearing housing
3260-01 Bearing cover
3260-02 Bearing cover
3712 Bearing nut
3852 Constant level oiler
3853 Grease nipple
3863 Grease regulator
4120 Gland
4130 Gland packing
4134 Lantern ring
4200 Mechanical seal
4213 Carrier for mechanical seal
4590-01 Gasket
4590-02 Gasket
4590-03 Gasket
4590-04 Gasket
4590-05 Gasket
Item Designation
4590-06 Gasket
4590-07 Gasket
4590-08 Gasket
4590-09 Gasket
4610-01 O-ring
4610-02 O-ring
6515 Drain plug
6521 Vent plug
6541 Lock washer
6544 Circlips
6569-01 Screwed plug
6569-02 Screwed plug
6569-03 Screwed plug
6569-04 Screwed plug
6569-05 Screwed plug
6569-06 Screwed plug
6570-01 Hexagon socket grub screw
6570-02 Hexagon socket grub screw
6572-01 Stud
6572-02 Stud
6572-03 Stud
6577-01 Hexagon bolt
6577-02 Hexagon bolt
6577-03 Hexagon bolt
6577-04 Hexagon bolt
6581-01 Hexagon nut
6581-02 Hexagon nut
6581-03 Hexagon nut
6810 Grooved pin
6700-01 Key
6700-02 Key
9331 Cover plate
8.3 General arrangement drawing
The typical general arrangement drawing and any
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the
User Instructions. If required, copies of other
drawings sent separately to the Purchaser should
be obtained from the Purchaser and retained with
these User Instructions.
9 CERTIFICATION
Certificates determined from the Contract
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for
retention with these User Instructions.
10 OTHER RELEVANT
DOCUMENTATION AND MANUALS
10.1 Supplementary User Instructions
Supplementary instructions such as for a driver,
instrumentation, controller, seals, sealant system
etc are provided as separate documents in their
original format. If further copies of these are
required they should be obtained from the supplier
for retention with these User Instructions.
10.2 Change notes
If any changes, agreed with Flowserve, are made to
the product after its supply, a record of the details
should be maintained with these User Instructions.
10.3 Additional sources of information
Reference 1:
NPSH for Rotor dynamic Pumps: a reference
guide, Euro pump Guide No. 1, Euro pump &
World Pumps, Elsevier Science, United Kingdom,
1999.
Reference 2:
Pumping Manual, 9
th
edition, T.C. Dickenson,
Elsevier Advanced Technology, United Kingdom,
1995.
Reference 3:
Pump Handbook, 2
nd
edition, Igor J. Karassik et al,
McGraw-Hill Inc., New York, 1993.
Reference 4:
ANSI/HI 1.1-1.5, Centrifugal Pumps -
Nomenclature, Definitions, Application and
Operation.
Reference 5:
ANSI B31.3 - Process Piping.