Flowserve Logix 520MD+ DD - Manual (Page 18)

DD User Manual - Logix® 520MD+ Series Digital Positioner FCD-LGENSF0013-01
© Flowserve Corporation
18
View the severity of the Command Frequency warning based
on the Start and End limits.
7.4.7.5 Command Amplitude
View the typical amplitude of the command input.
7.4.7.6 Command Amplitude Hi Start Limit
Set the limit at which the Command Amplitude warning will
appear.
7.4.7.7 Command Amplitude Hi End Limit
Set the limit at which the Command Amplitude warning will
show full severity.
7.4.7.8 Command Amplitude Hi Percent Warning
View the severity of the Command Amplitude warning based
on the Start and End limits.
7.4.7.9 Position Frequency
View the typical frequency of the position cycling in
cycles/hour.
7.4.7.10 Position Frequency Hi Start limit
Set the limit at which the Position Frequency warning will
appear.
7.4.7.11 Position Frequency Hi End Limit
Set the limit at which the Position Frequency warning will
show full severity.
7.4.7.12 Position Frequency Hi Percent Warning
View the severity of the Position Frequency warning based
on the Start and End limits.
7.4.7.13 Position Amplitude
View the typical amplitude of the valve position.
7.4.7.14 Position Amplitude Hi Start limit
Set the limit at which the Position Amplitude warning will
appear.
7.4.7.15 Position Amplitude Hi End Limit
Set the limit at which the Position Amplitude warning will
show full severity.
7.4.7.16 Position Amplitude Hi Percent Warning
View the severity of the Position Amplitude warning based on
the Start and End limits.
7.4.8 Valve travel/Cycles
View and adjust the limits for the valve cycling and travel
warnings.
7.4.8.1 Valve Travel
View the total valve travel.
7.4.8.2 Valve Travel Hi Start Limit
Set the limit at which the Valve Travel warning will appear.
7.4.8.3 Valve Travel Hi End Limit
Set the limit at which the Valve Travel warning will show full
severity.
7.4.8.4 Valve Travel Hi Percent Warning
View the severity of the Valve Travel warning based on the
Start and End limits.
7.4.8.5 Valve Travel Dead Band
Set the amount the valve must move in order to begin adding
to the travel total.
7.4.8.6 Valve Cycles
View the total valve cycles.
7.4.8.7 Valve Cycles Hi Start Limit
Set the limit at which the Valve Cycles warning will appear.
7.4.8.8 Valve Cycles Hi End Limit
Set the limit at which the Valve Cycles warning will show full
severity.
7.4.8.9 Valve Cycles Hi Percent Warning
View the severity of the Valve Cycles warning based on the
Start and End limits.
7.4.8.10 Valve Cycle Dead Band
Set the amount the valve must move in order to begin adding
to the travel and cycle totals.
7.4.8.11 Stroke Length
Enter the stroke length of the valve.
7.4.8.12 Valve Travel/Cycles Reset
Reset the valve travel or cycle counter.
7.4.9 Actuator Travel/Cycles
View and adjust the limits for the actuator cycling and travel
warnings.
7.4.9.1 Actuator Travel
View the total actuator travel.
7.4.9.2 Actuator Travel Hi Start Limit
Set the limit at which the Actuator Travel warning will appear.
7.4.9.3 Actuator Travel Hi End Limit
Set the limit at which the Actuator Travel warning will show
full severity.
7.4.9.4 Actuator Travel Hi Percent Warning
View the severity of the Actuator Travel warning based on
the Start and End limits.
7.4.9.5 Actuator Cycles
View the total actuator cycles.
7.4.9.6 Actuator Cycles Hi Start Limit
Set the limit at which the Actuator Cycles warning will
appear.
7.4.9.7 Actuator Cycles Hi End Limit