Interactive Toy Concepts Ironman User Manual

Interactive Toy Concepts Toys

Advertising
background image

Lightstars is a registered trademark of Interactive Toy Concepts Ltd. © 2013 All Rights Reserved.

Manufactured by and distributed by Interactive Toy Concepts Ltd. Conforms to Safety Standards ASTM F963 Regulatory Requirements

Meets CPSC Safety Requirements. Products and colors may vary. MADE IN CHINA.

INS-22008-130527-US

Limited 30-day warranty

Product is warranted by Interactive Toy Concepts Limited against

manufacturing defects in material and workmanship under normal use

for (30) days from the date of purchase.
Warranty is validated upon receipt of proof or purchase

and confirmation of UPC code.

Proof of Purchase

PLEASE! DO NOT RETURN THIS PRODUCT TO ANY RETAIL STORE!

For any questions or problems with this product please contact us at:Email: [email protected]

Phone: Inside North America: +1-416-444-6873 Outside North America: 1-866-214-2220

Address: Interactive Toy Concepts, 17 Vulcan Street, Toronto, Ontario, Canada. M9W 1L3 Website: www.interactivetoy.com

Welcome to the Light Stars animated hologram projector

from Interactive Toy Concepts!

The Light Stars requires 4 x AAA batteries to operate!

Alakaline batteries are recommended for best performance.

IMPORTANT: This product includes ‘try-me’ batteries.

Used for demonstration purposes only. Before use, remove

the try-me batteries and replace with the appropriate

batteries specified in this guide.

5+

Item #

22003/22030/22031

22032/22035/22036

22038/22039/22050

22051/22052/22053

22055/22056

1. Open the battery compartment door

located at the bottom of the Light

Stars unit by using a Phillips

screwdriver (not included).

2. Insert the batteries as shown.

Ensure that the + or – polarities match

the illustrations inside the battery

compartment.

3. Replace the battery compartment

door and tighten the screw. Do not

over tighten.

-

+

-

+

-

Manufactured by and distributed by Interactive Toy Concepts Ltd.

Conforms to Safety Standards ASTM F963 Regulatory Requirements

Meets CPSC Safety Requirements.

Products and colors may vary.

MADE IN CHINA.

©

IMPORTANT BATTERY INFORMATION

Do not mix old and new batteries, different types of batteries, standard carbon zinc, or alkaline batteries of different capacities. Do not use

rechargeable batteries. Ensure that the contact surfaces are clean and bright before installing new batteries. Please match the correct polarity (- or

+) when replacing batteries. Do not throw batteries into the fire. Replace all batteries of the same type/brand at the same time. The supply

terminals are not to be short-circuited. Remove exhausted batteries from the toy. Batteries should be replaced by adults. Remove batteries if the

toy is not going to be played with for a long time to prevent leakage or other damage. Non-rechargeable batteries are not to be recharged.

Rechargeable batteries are only to be charged under adult supervision. Rechargeable batteries are to be removed from the toy before being

charged. For optimal performance, use only alkaline batteries.

IMPORTANT SAFETY INFORMATION

Do not modify your LIGHT STAR! Any changes or modifications to this product are strictly prohibited and will void product warranty.

ADULT SUPERVISION IS RECOMMENDED AT ALL TIMES!

INSTALLING / REPLACING

BATTERIES (only by Adult)

CONTROL INSTRUCTIONS - OPERATING THE LIGHTSTAR TOY

POWER

ON / OFF

Button

Chapter

Selection

Button

Action

Buttons

POWER ON / OFF Button

Press and hold the POWER button for 1 second, the Light Stars unit will

power on. Repeat the above to power off.

The Light Stars unit is programmed with a power saving feature. The

built-in LED will turn off automatically after 30 seconds if there are no

actions or selection button inputs. The LED will resume operation when

there is any input from an action button.

* If the Light Stars unit is not used continuously for another 30 seconds it

will automatically power off completely.

* If you cannot power on the Light Stars Unit, or the LED is dim after the

unit is turned on, the batteries may have run out of power and need to be

replaced.

* Please follow the instructions in this manual to replace the batteries.

Chapter Selection Button

To cycle through all the different chapters of animations. Pressing this

button takes you to a new chapter where different actions can take

place. Each chapter has its unique actions.

Action Buttons

To activate the playback of different actions which are a unique part of

each chapter.

AGES:

HOLOGRAM PROJECTION FOCUS ADJUSTMENT

If your hologram projection is out of focus, you can adjust this by rotating the focus ring near the top of your Light Stars toy.

Package Contents:

1 x Light Stars Animated Hologram Projector

1 x Instruction Manual

Advertising
This manual is related to the following products: