Desa EFS33NR EU - Manual (Page 17)

107172-01G
17
17
For more information, visit www.desatech.com For more information, visit www.desatech.com
Shutting Off Heater
1. Turn control knob clockwise to the OFF position.
2a. Set selector switch in the OFF position.
2b. If Using Optional Hand-Held Remote: Set selector switch in
the OFF position to keep from draining battery.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
• Turn control knob clockwise to the PILOT position.
• Use remote control manual OFF button.
• Set selector switch in the OFF position.
Figure 34 - Pilot (Propane/LP)
Ignitor
Electrode
Pilot Burner
Figure 33 - Pilot (Natural)
Pilot Burner
Ignitor
Electrode
TO TURN OFF GAS
TO APPLIANCE
OPERATING FIREPLACE
Continued
OPERATING FIREPLACE
Lighting Instructions (Cont.)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Remote Operation
1. Follow steps 1 through 6 under Lighting Instructions, page 16.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow
steps 9 through 11, page 16.
MANUAL LIGHTING
PROCEDURE
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position (see Figure 35).
Note: The burn-
ers may light if hand-held remote ON button was on when
selector switch was last turned off. You can now turn the
burners on and off with the hand-held remote control unit.
IMPORTANT : Do not leave the selector switch in the REMOTE
position when the pilot is not lit. This will drain the battery.
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
GHRCTA Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 36, page 18). The lights to the left of the
button will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held remote
unit controls the room temperature. To increase the room
temperature, press the top arrow of the TEMP button. To
lower the room temperature, press the bottom arrow of the
TEMP button. At higher settings the heater will run longer.
IMPORTANT: This remote control has been specially en-
gineered to take an air temperature sample every minute
in the auto mode. It will not respond immediately to the
temperature setting being turned up or down.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions on page 16.
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, pages 28 through 30). Follow instruc-
tions included with the remote control.
Thermostat Control Operation
(Optional GHRCTA Series Only) The thermostat control set-
ting on the remote control unit can be set to any comfort level
between WARMER and COOLER. The burners will turn on
and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending
upon the amount of space to be heated, the output of the central
heating system, etc.
For wall thermostat operation, follow instruction supplied with
thermostat accessory GWMT1. For wall switch operation fol-
low instructions supplied with GWMS2.
Figure 35 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
O
FF
PIL OT
O
N
LO
IH
ON
OFF
REMOTE
Selector Switch in Remote Position
(Optional Remote Control)
Flame Adjustment Knob
Control Knob in
On Position