Marantz ST-17 - Manual (Page 8)

6
ENGLISH
F
RAN
Ç
AIS
HOW TO PRESET A FREQUENCY IN THE MEMORY
1. Select FM or AM with the BAND button.
2. Select the desired station with the GYRO CONTROL ring.
3. Press the MEMO button.
“MEMORY” will flash on the display.
4. While the “MEMORY” indicator is flashing (approx. 5 sec.), turn the
GYRO CONTROL ring to the left or right to select the desired preset
number.
5. Press the MEMO button again.
The “MEMORY” indicator will go out, and memorization will be
finished.
CALLING UP STORED STATIONS
1. Confirm that the “PRESET” indicator is lit on the display. If not lit,
press the PRESET button to turn it on.
2. Turn the GYRO CONTROL ring to select the desired preset station.
DELETING THE CONTENTS OF THE PRESET MEMORY
1. Select the preset station you wish to delete.
2. Press the MEMO button.
The “MEMORY” indicator will flash on the display.
3. While the “MEMORY” indicator is flashing (approx. 5 sec.), turn the
GYRO CONTROL ring to set the preset number to “00”.
4. Press the MEMO button again.
The preset number and the “CLEAR” indicator will flash for approx. 2
seconds on the display and the memory will be deleted.
Station names memorized for the preset station will also be deleted at
the same time.
<GYRO RING operation method>
When the GYRO ring is turned to the right, the frequency or preset
number will increase, and when turned to the left, they will decrease.
STEREO TUNER ST-17
A B WIDE NARROW
BAND MEMO MONO IF BAND FM ANTENNA POWER DISPLAY ST NAME PRESET TUNING AUTO
MEMORY
4
1
2, 4
3, 5
1. Select and display the preset channel you wish to register.
2. Press the ST NAME button.
The display’s frequency indicator will go out, “MEMORY” will flash
and “_ _ _ _ _ _ _ _” will appear.
INPUT OF STATION NAMES ON THE
MAIN UNIT
The display automatically shows the name of an RDS station when it is
being received.
It is also possible to have the station name of a non-RDS station
displayed by entering the station name manually.
HOW TO INPUT A STATION NAMES
STEREO TUNER ST-17
A B WIDE NARROW
BAND MEMO MONO IF BAND FM ANTENNA POWER DISPLAY ST NAME PRESET TUNING AUTO
1
5
3
2, 4
* When a station other than a preset station is selected, and the CHAR.
button is pressed, the frequency indicator will remain lit, the
“PRESET” indicator will flash and the station name can not be
registered.
3. Use the GYRO CONTROL ring to input the desired number or letter at
the first flashing digit on the left side.
When the GYRO CONTROL ring is turned to the right, input will
change in the following order: A – Z
Ǟ _ Ǟ ѿ Ǟ . . Ǟ 0 – 9 Ǟ A –.
When turned to the left, input will change in the following order: 9 – 0
Ǟ . . Ǟ ѿ Ǟ _ Ǟ Z – A Ǟ 9 –. (“_” indicates a space.)
4. Press the ST NAME button when the first digit on the left has been
input.
Flashing will move to the second digit. Input the desired number or
letter using the same procedure as in step 3, and press the CHAR.
button.
Repeat this procedure to input up to 8 characters.
(The flashing position will move each time the ST NAME button is
pressed.)
5. When the desired station name has been input, press the MEMO
button.
Flashing will stop and registration will be finished.
* Although station names of up to 8 characters can be input, even if a
station name that is under 8 characters is input, pressing the MEM0
button will finish registration at that point.
CHANGING STATION NAME
To change registered station names, carry out steps 2 to 5 of the
registration procedure. The old station name will be replaced with the
new one.
TO ERASE STATION NAMES
1. Display the station name to be erased.
2. Input spaces ( _ ) at all 8 digits.
3. Press the MEMO button. The station name will be erased, and the
frequency display will be returned to.
Blinking