Marantz PS-17 - Manual (Page 37)

27
ENGLISH
PROGRAMMING MACROS
Macros make it possible to use a single function button to perform
more complex series of operations that would normally require
pressing several buttons. A single button can be programmed to
perform up to 10 steps in sequence. A typical example of such a
series might be as follows:
• Turn the main amplifier power ON
fi Switch the function to LD fi
Set the Surround Mode to Pro Logic fi Switch the TV to video input
fi Set the laser disc player to PLAY.
• No signals may be transmitted during macro programming.
• The various steps that make up a macro are set initially to be sent
one after another in 1 second intervals, however these intervals
may be shortened to as little as 0.5 seconds or lengthened to as
much as 5 seconds using the Setup mode.
• In the macro mode, the number of steps the macro contains is
displayed on LCD c. Macros may be programmed for each of the
11 function buttons, from LD to AMP.
1. Use a ballpoint pen or other sharp point to press the MACRO
button x until the MACRO and LEARN indicators are displayed
blinking on the LCD.
2. Press the Function button , for which you wish to program a
series of operations. In this case, let’s use the example of the
laser disc player.
Press the
LD Function button ,. The LCD a will display LD-M.
Characters displayed on LCD a include the following,
depending on the function button for which the macro is being
programmed:
LD-M, DVD-M, TV-M, DSS-M, VCR-M, AUX-M, TUN-M, CD-M, TP-
M, AMP-M, CDR-M (or MD-M for remote controller set for MD).
• If a macro has already been set for the selected function
button, the LCD a will blink. Also, the number of steps in the
macro is displayed on LCD c.
3. Erasing Jog Dial Codes
To clear all codes and names previously set for each of the
functions (LD, TV, etc.).
1) Press the function you want to erase.
2) Hold down the CLEAR button ⁄5 and press both ENT
buttons m at the same time. LCD b will display CLR? .
3) If you wish to continue the clearing operation, press the OK
Cursor button ⁄0. This will return all 10 commands in the Jog
Dial to their factory presets, or leave them empty if no factory-
presets are available. Accordingly, the LCD
b will return to
the factory preset displays, or will simply be empty.
• Use a similar operation to erase the Jog Dial codes for each
function.
• To cancel the memory clearing operation, do not press OK
Cursor button ⁄0 and simply touch any other button.
4. Erasing Code s by Function
To clear all codes and names previously set for each of the
functions (LD, TV, etc.), press and hold the
CLEAR button ⁄5,
then press the button for the function to be cleared twice. CLR?
will appear on LCD b. If you wish to continue the clearing
operation, press the
OK Cursor button ⁄0.
This will return the button to its factory-presets or leave it empty if
no factory presets are available. Accordingly, the LCD b will
return to the factory preset displays, or will simply be empty.
• To cancel the memory clearing operation, do not press the
OK Cursor button ⁄0 and simply touch any other button.
• The codes for the < • 3 button ⁄1 cannot be cleared.
MEMO GUIDE MUTE
CH VOL
1 2 3 4 5
C D DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
OK
2
L D
ENT ENT
CLEAR
CH VOL
C D DVD CD-R/MD
OK
MEMO GUIDE MUTE
1 2 3 4 5
C D DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR
ON OFF ON / OFF
SOURCE
MACRO MODE
LEARNING REMOTE
CONTROL RC-17PS
POWER