Marantz PS-17 - Manual (Page 38)

28
ENGLISH
3. While pressing the VOL button ., use the ^ and
v Cursor
buttons ⁄0 to call up the portion of the macro to be changed.
Pressing the ^ button advances through the macro steps and
pressing the
v button regresses through the macro steps.
• To rewrite an existing macro step, simply press the button for
the new step. The old step will be erased and rewritten with
the new step.
• To insert a new step in between existing steps in a macro,
after step 3 press the MEMO button ⁄6 , then press the button
for the new step. The numbers of the other steps will be
adjusted accordingly to accommodate the new step. Since
only 10 steps may be stored in any macro, the tenth step will
be erased if an step is inserted when the total number of
steps is already 10.
• To erase a step in a macro, after step 3 call up the number of
the step to be erased and press the CLEAR button ⁄5.
• If while editing macros no buttons are pressed for
approximately 1 minute, the remote controller will
automatically return to normal mode, and no macro changes
will be programmed in the memory.
4. When you are finished editing macros, use a ballpoint pen or
other sharp point to press the
MACRO button x. END will be
displayed on LCD a and the display will return to normal.
USING MACROS
The following procedure will show how to use the function buttons for
which you have programmed macros.
1. Press the Function button , for the desired macro for 3
seconds. MACRO is displayed on LCD a for approximately 1
second, after which the number of steps in the macro is
displayed on LCD c.
• The remote controller will do nothing if no macros are
programmed. The macro steps are executed in order and the
names of their buttons are displayed on the LCD. Also, the
step numbers displayed on LCD c disappear as each step is
executed.
2. After all macro commands have been transmitted, the remote
controller returns to normal mode.
• To cancel the transmission of a programmed macro, use the
Cursor buttons ⁄0 to press 7.
3. Press the buttons for the operations you wish to program as a
macro in the sequence you want the macro to program them. The
name of the button pressed appears on LCD a. The number of
steps in the macro is displayed on LCD c and this number
increases by 1 with each button pressed.
For example, press LD, PLAY.
Each function button can be programmed to perform up to 10
steps in sequence.
• If, while programming, no buttons are pressed for
approximately 1 minute, the remote controller will
automatically return to normal mode, and no macro will be
programmed in the memory.
4. When you are finished programming macros, use a ballpoint pen
or other sharp point to press the
MACRO button x. LCD a will
display END , and the display will return to normal.
• Macros cannot be programmed for the MODE z, MACRO
x, < • 3 ⁄1, VOL / ., MEMO ⁄6 or CLEAR ⁄5 buttons.
In the macro mode it is possible to program the memory to
perform macros containing up to 10 steps.
Each of the function operations (11 including CD, DVD, etc.)
can be used in a macro more than once, however for all
except AMP, only the first function operation will be
transmitted as a signal from the remote controller.
Accordingly, within a single macro, it is not possible to switch
between multiple function operations. (This is to prevent the
switching of the receiver function operation.) Within a macro,
the second time a function operation is used, it will only be
used on the remote controller itself and no signal will be
transmitted to the component.
EDITING MACROS
Macros may be edited using following procedure.
1. Use a ballpoint pen or other sharp point to press the MACRO
button x until the MACRO and LEARN indicators are displayed
blinking on the LCD.
2. Press the Function button , to be changed. Let’s use the
example of the laser disc player, by pressing the LD Function
button ,.
• LD-M is displayed blinking on LCD a.
• The number of steps in the completed macro is highlighted
on LCD c. In this example there are 3 macro programs in
memory.
The is highlighted if no macros have been programmed,
and the remote controller is ready for macro programming.
MEMO GUIDE MUTE
CH VOL
1 2 3 4 5
6 7 8 0 9
C D DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR
OK
CH VOL
C D DVD CD-R/MD
DSS T V VCR PHONO
OK
GUIDE MUTE
1 2 3 4 5
6 7 8 0 9
TUNER TAPE
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR MEMO
MEMO GUIDE MUTE
1 2 3 4 5
6 7 8 0 9
TUNER TAPE
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR
MEMO CLEAR GUIDE MUTE
1 2 3 4 5
6 7 8 0 9
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D