Microsonic esf-1/CF User Manual
Page 2
2004/108/EG
Standard Teach-in methods
Dynamic Teach-in of
label
Insert the backing
material with label
into the fork.
Static Teach-in of
label
a) Only insert backing
material into the
fork.
Teach-in only for
sheeting
(splice sensor)
Insert web material
into the fork.
QuickTeach
Activate QuickTeach
Turn off operating
voltage.
Press push-button
1)
for 3 s, until red LED
is off and yellow and
green LED flash
mutually.
LED red:
LED green:
LED yellow:
Pull the backing ma-
terial with label
through the fork at a
constant speed.
off
flashes briefly
on
Press push-button
1)
for 1 s.
Press push-button
1)
for 6 s, until red and
yellow LED are off
and green LED
flashes.
LED red:
LED green:
LED yellow:
Pull some backing
material through the
fork.
off
flashes briefly
on
Press push-button
1)
for 1 s
LED red:
LED green:
LED yellow:
b) Place label on
backing material into
the fork.
on
flashes briefly
off
Press push-button
1)
for 9 s, until red and
green LED are off
and yellow LED
flashes.
LED red:
LED green:
LED yellow:
Pull web material
(without splice)
through the fork.
off
flashes briefly
on
Press push-button
1)
for 1 s.
Press push-button
1)
.
Turn on operating
voltage.
Hold down push-but-
ton
1)
for 6 s, until red
and green LED light
up and yellow LED
flashes.
LED yellow: flashes briefly:
QuickTeach
label sensor
or
Press push-button
1)
for 1 s
LED red:
LED green:
LED yellow:
on
flashes briefly
off
Move the label on
the backing material
in the fork.
Press push-button
1)
for 1 s.
Normal operation
1) All settings via push-button can alternatively be made by connecting the Teach-in/control input Com to +U
B
.
LED red:
LED green:
To switch modes,
press push-button
1)
.
flashes briefly:
QuickTeach
splice sensor
oder
flashes briefly:
Standard Te-
ach-in method
Do not press push-
button
1)
for 10 s.
Normal operation
QuickTeach
label sensor
Insert backing mate-
rial with label into
the fork.
QuickTeach
splice sensor
Insert web material
into the fork.
Press push-button
1)
(LED red: off, LED
green: flashes, LED
yellow: on) and con-
tinue to hold it down.
Pull the backing ma-
terial with labels
through the fork at a
constant speed.
Press push-button
1)
(LED red: off, LED
green: flashes, LED
yellow: on) and con-
tinue to hold it down.
Pull web material
(without splice)
through the fork.
Further settings (only available in standard Teach-in methods)
Adjusting label/
splice
output F to NCC/NOC
Enable/disable Teach-
in push-button
1)
Turn off operating
voltage.
Press push-button
1)
for 13 s, until red LED
comes on and green
and yellow LED flash
simultaneously.
LED red:
LED green:
LED yellow
on
flashes briefly
on: output F
set for label/
splice
off: output F
not set for la-
bel/splice
Press push-button
1)
.
Turn on operating
voltage.
Press push-button
1)
for 3 s, until red LED
comes on and green
and yellow LED flash
mutually.
LED red:
LED green:
LED yellow
on
flashes briefly
on: push-but-
ton disabled
off: push-but-
ton enabled
Release
push-button
1)
.
Release
push-button
1)
.
To switch the
output function,
press push-button
1)
.
Do not press push-
button
1)
for 10 s.
To switch function,
press push-button
1)
.
Do not press push-
button
1)
for 10 s.
Normal operation
Reset to factory set-
ting
Turn off operating
voltage.
Press push-button
1)
.
Turn on operating
voltage.
Press push-button
1)
for 10 s until red and
yellow LED light up
and green LED
flashes.
Release push-but-
ton
1)
, before
the operating volta-
ge is turned off.
a)
b)