QuickLabel QLS-4100 Xe - Manual (Page 215)

QLS-4100 Xe Menus
Pause Pause: Cal & Setup
Press SELECT
Pause: Ribbon
Press SELECT
Pause: Options
Press SELECT
Pause: Communication
Press SELECT
Pause State
Pause: System
Press SELECT
Pause: Adjust
Press SELECT
Pause: Operation
Press SELECT
Pull Back
Disabled
Applicator
Enabled 1
Mirror Mode
Off
Cut Flag
OFF
Cutter
Enabled
Parallel
Parallel Mode
Auto
RS232 Baud Rate
19200
RS232 Handshaking
Hardware
TCP/IP Address
172.16.2.255
TCP/IP Subnet Mask
255.255.3.255
TCP/IP Gateway
0.0.0.0 Two
TCP/IP Connections Data Port
Ribbon Sensor
Enabled
Ribbon Type
Standard
Drop Adjust
Head 1 = 22 Drop Adjust
Head 2 = 22 Drop Adjust
Head 3 = 22 Drop Adjust
Head 4 = 22
Synchronize Labels
Press SELECT
Pull Back
Press SELECT
Label Reprint
Copies = 1
Calibrate
Continuous
Test Print
Test Pattern: = 1 in
Printer Settings
Press SELECT
Horizontal
Baseline = +0
Cutter Baseline
Offset = +0
Vertical
Baseline = +0
Intensity
Head 1 = 16
Prnt Line Adj
Head 1 = +0
Prnt Line Adj
Head 2 = +0
Intensity
Head 2 = 16
Intensity
Head 3 = 16
Intensity
Head 4 = 16
Speed
3 in/s
Prnt Line Adj
Head 3 = +0
Cross Web Adj
Head 1 = <-2
Cross Web Adj
Head 2 = <-2
Cross Web Adj
Head 3 = <-2
Cross Web Adj
Head 4 = <-2
Vertical
Offset = +16
Horizontal
Offset = -20
Cut Offset
+0
P r e s s S E L E C T
P r e s s S E L E C T
P r e s s S E L E C T
P r e s s S E L E C T
P r e s s S E L E C T
P r e s s S E L E C T
P r e s s S E L E C T
Memory Card
Write Protect ON
Display Cntr
Off
Format Memory Card
Press SELECT
Time
10:42 am
Date
2002, Sep 19
Factory Reset
Press SELECT 0000
Front Panel Lock
3
4
7
Form Stop Adjust
+0 (+0.0 mm)
8
Peel Delay
Delay = +0.0 sec
9
5 6
Ready State
Ready: Intensity
Head 1 = 16
Ready: Prnt Line Adj
Head 1 = +0
Ready: Cross Web Adj
Head 1 = <-2
Ready: Intensity
Head 2 = 16
Ready: Intensity
Head 3 = 16
Ready: Intensity
Head 4 = 16
Ready: Prnt Line Adj
Head 2 = +0
Ready: Prnt Line Adj
Head 3 = +0
Ready: Cross Web Adj
Head 2 = <-2
Ready: Cross Web Adj
Head 3 = <-2
Ready: Cross Web Adj
Head 4 = <-2
Ready: Speed
3 in/s
Ready
0015 of 0050
1 2 8
Ready:Cut Offset
+0
Ready: Vertical
Offset = +16
Ready:Horizontal
Offset = -20
Ready: Label Reprint
Copies = 1
Ready: Display Cntr
Off
Ready: Form Stop Adj
+0 (+0.0 mm)
9
Ready: Peel Delay
Delay = +0.0 sec
1 Cut Offset option appears only if Cutter is enabled.
3
Format Memory Card option provides a confirmation
menu to prevent accidental formatting.
4
Pull Back option available only if the Pull Back
function is enabled.
5
Label Reprint option available only if a label was
previously printed. (requires Window driver)
6 Synchronize Labels option available only when
using one of the following:
- External applicator system
- Print & Peel multiple label mode
7 Cut Offset option appears only if Cutter is enabled.
8
Form Stop Adjust option only available in Print & Peel
single label mode.
9
Peel Delay option only available in Print & Peel
mode (single label or multiple label).
2
Label Reprint option appears only if a label was
previously printed. (requires Windows driver) To enter a sub menu, scroll to the sub menu with
the left/right arrow keys, then press the SELECT key.
—
To change values in a sub menu, scroll values with
the up/down arrow keys, then press the SELECT key.
—
To scroll values quickly, press and hold the appropriate
arrow key. Values will scroll faster while keys are held.
—
—
To return to the high level Pause menu, press
the PRINT/PAUSE key.
Maximum Gap (mm)
Max Gap = 0
Ignore Host Commands
Disable
"No Air" Warning
Disabled
Image Normalization
Disabled
System Configuration
Standard
Print & Peel Mode
Off