Epson AVR-687 User Manual
Page 47
ENGLISH
44
ENGLISH
Advanced Setup – Part 1
Advanced Setup – Part 1
Setting the 2ch Direct/Stereo Custom
Make the 2-channel direct mode and stereo mode speaker settings.
Press
F
F
to select “ON”, then press
H
H
.
1
Large:
Select this when using large speakers with ample low frequency
reproduction capabilities.
Small:
Select this when using small speakers without ample low
frequency reproduction capabilities.
Press
D
D H
H
to select the item, then press
F
F G
G
to set.
2
1
2
A
u
t
o
S
u
r
r
.
O
N
3
5
2
c
h
C
s
t
m
O
N
1
6
2
c
h
F
L
a
r
g
e
2
7
2
c
h
S
W
Y
e
s
8
2
c
h
L
F
E
N
o
r
m
9
2
c
h
F
L
1
2
f
t
1
1
2
c
h
F
r
e
q
8
0
LFE (Normal):
For any channel(s) that are set to “Large”, low frequencies in that
channel’s corresponding source are directed to that loudspeaker
only. The low frequencies played from the subwoofer are only the
LFE signals and the low frequencies of channels set to “Small”.
LFE+Main:
Low frequencies from speaker channels that have been set to
“Large” are reproduced from those speakers as well as from the
subwoofer(s).
Yes, No:
Select “Yes” when a subwoofer is connected, “No” when no
subwoofer is connected.
Press
ENTER
or
H
H
to enter the setting and switch to
the Auto Surround Mode setting.
3
5
2
c
h
C
s
t
m
O
F
F
2
3
P
.
O
n
L
A
S
T
4
M
u
t
e
F
U
L
L
2
L
i
m
i
t
-
1
0
d
B
1
Setting the Volume Control
This sets the volume level of output.
Press
D
D H
H
to select the item, then press
F
F G
G
to set.
Volume Limit:
Set the volume’s upper limit.
• 0 dB, –10 dB, –20 dB:
The volume cannot be increased above the selected levels.
• OFF:
If you do not want to set a volume limit, select “OFF”.
In this case, the volume can be set to the AVR-687’s maximum
volume (output) level of +18 dB, which is extremely loud.
1
Muting Level:
Set the level of volume attenuation in the mute mode.
• FULL:
The volume is fully muted.
• –40 dB, –20 dB:
The volume is lowered 40 dB or 20 dB from the current level.
Power On Volume Level:
• LAST:
The volume set when the AVR-687 was last used is stored in the
memory and set when the power is turned on.
• – – – (Mute):
The volume is always muted when the power is turned on.
• –80 dB ~ +18 dB:
Set the volume level when the power is turned on.
You can adjust the MAIN ZONE volume level within the range of
–80 to +18 dB (and ZONE2 volume level within the range of –70 to
+18 dB).
Press
ENTER
or
H
H
to enter the setting and switch to
the 2ch Direct/Stereo Custom setting.
2
1
0
2
c
h
F
R
1
2
f
t
Crossover Frequency (40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz):
Set as desired according to your speakers’ bass playback ability.