Sealey PC200SDAUTO - Manual (Page 2)

pc200sdauto.v3 Issue no.2 19/10/09 Original Language Version
3. CONTENTS
3.1 Carton content
3.1.1 carefully unpack the carton.
3.1.2 Locate the two side latches (fig.1.19) which hold the power
head in place.
3.1.3 undo the latches, remove the top section and take out the
items in the container.
3.1.4 check and identify each component as listed below. If anything
is missing or damaged please contact your supplier
immediately.
Item Description
1 Flexible vacuum hose
2 noise diffuser
3 telescopic suction tube
4 Instruction manual
5 Wheel (x2)
6 combination nozzle
7 vacuum hose connection
8 crevice nozzle
9 dust free tool adaptor
part no.pc200sdav3.42
10 Foam filter
Item Description
11 Locking cartridge Filter
(fitted as standard)
12 castors & foot (x2)
13 Four screws in bag
14 drain cap
15 container, (stainless steel)
16 dust free tool socket
17 on/oFF switch, 3 position
18 Handle
19 clasp, one either side (x2)
fig 1
4. ASSEMBLY
4.1 Ensure the mains plug is disconnected.
4.2 undo latches that secure the power head to the stainless
container.
4.3 Lift off the power head and put carefully to one side.
4.4 Locate the castor feet and wheels ready for fitting.
4.5a turn the container upside down. the castor feet attach to
the lower moulding using a dovetail arrangement. slot each
foot in turn into the receiving slots either side of the drain
cap and push fully home. Retain each castor foot with the
self tapping screws provided.
4.5b the rear wheels attach to the lower moulding in the same
way but they are handed. Match the moulded in number on
each wheel assembly to the numbers on the lower moulding
and push fully home. Retain each wheel assembly with the
self tapping screws provided.
4.6 For dry vacuum cleaning use the locking cartridge filter supplied.
NOTE: Do not operate the cleaner without a cartridge
filter fitted as this will damage the machine and invalidate
your warranty. Ensure the filter is correctly fitted before
every use.
4.7 If wet vacuuming remove the cartridge filter and push the
foam filter over the filter basket instead.
4.8 Replace the top section onto the container.
4.9 align up the top section with the latches and snap into place,
by applying pressure at the mid point of the clasps.
4.10 Insert the large end of the hose into the front inlet of the
container and lock in place by turning clockwise a quarter
turn.
4.11 choose the desired nozzle and push it onto the telescopic
suction tube.
4.12 For quiet operation, install the noise diffuser (fig.1-2) into the
blower port by inserting the locking end into the blower port
and turning it clockwise to lock it in place.
2. INTRODUCTION & SPECIFICATION
Introduction: powerful 1400Watt motor head gives incredible
suction through Ø35mm hosing. May also be used as a blower.
Integral three-pin Bs socket provides power supply for dust-free
tools up to 1400W. When used in conjunction with a power tool the
cleaner auto-starts when the tool is started and auto-stops 10
seconds after the tool is switched off to ensure tool and hose are left
free of dust. Includes stainless steel drum on two castors and two
fixed wheels & stainless steel telescopic rigid extension tube as well
as tools for wet and dry operations. tool stowage points on head and
base. supplied with cartridge filter and wet-use foam filter.
Specification
Motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230v 1400W
container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20ltr
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8kg
vac accessories Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35mm
Max vacuum pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165mbar
air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120m³/hr
Filter type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking cartridge