Sealey PC200SDAUTO - Manual (Page 4)

pc200sdauto.v3 Issue no.2 19/10/09 Original Language Version
10. MAINTENANCE
10.1 GENERAL MAINTENANCE.
10.1.1 Ensure the machine is unplugged from the power supply. (1)
10.1.2 disconnect the hose from the container. (2)
10.1.3 undo the clasps and remove motor head from the container. (3)
10.1.4 clear out any dirt or debris from the container and hose. (4)
10.1.5 check that the telescopic suction tube operates smoothly
and check the power cable to make sure it has not been
damaged.
10.2 CARE OF LOCKING CARTRIDGE FILTER
IMPORTANT! clean or change the cartridge filter regularly
for best performance and long product life. the cartridge
filter is essential for the proper functioning of the cleaner. If
the machine is used without a cartridge filter the motor
will burn out and the warranty will be voided. always
keep a new, spare filter on hand.
10.2.1 the cartridge filters supplied are made of a high quality
material designed to trap small dust particles and should
only be used for dry vacuum cleaning. If the cartridge filter
becomes wet it will clog very quickly and be very
difficult to clean. always handle filters very carefully when
removing and cleaning them. check the filter for tears or
small holes. Replace the filter if it is found to be damaged.
INSTALLING CARTRIDGE FILTER
10.2.2 Remove the power head and turn it upside down. With the
raised rim uppermost fit the cartridge filter tube down over
the filter basket and push fully home. place the locking disc
onto the top of the filter and turn the locking bar until the
latch drops into the slot in the top of the filter cage. continue
turning until the filter is fully locked down. (see a & B above).
11. TROUBLESHOOTING
12. CONSUMABLES
MODEL ..................................................................................................................................................................................PC200SDAUTO.V3
Locking cartridge Filter (Must be used for dry vacuuming) ................................................................................................. part no. pc200cFL
Foam Filter ......................................................................................................................................................................... part no. pc200FF10
dust Bags (optional) ...........................................................................................................................................................part no. pc200pB5
IMPORTANT! IF THE MACHINE IS USED WITHOUT A CARTRIDGE FILTER FITTED THE MOTOR WILL BURN OUT EVENTUALLY AND
YOUR GUARANTEE WILL BE INVALIDATED. ALWAYS KEEP A SPARE CARTRIDGE FILTER HANDY.
CLEANING CARTRIDGE FILTER
10.2.4 to remove the cartridge filter pull it carefully upwards and off
the filter cage. (c)
10.2.5 clean the cartridge by gently tapping it over a waste
receptacle or lightly brushing with a soft brush. do this
outdoors. (d)
10.2.6 If a cartridge filter becomes inadvertently wetted it should be
removed and allowed to air dry for 24 hours before reinstalling.
10.3 INSTALLING A FOAM SLEEVE FILTER
10.3.1 Remove the power head and turn it upside down. carefully
remove the cartridge filter and store safely for future use.
10.3.2 slide the foam sleeve filter down over the filter cage ensuring
that the whole cage is covered. see 1 & 2
10.3.3 Invert the power head and refit it onto the container
CLEANING A FOAM SLEEVE FILTER
10.3.4 carefully remove the foam sleeve from the filter cage.(3)
10.3.5 Wash the foam sleeve in a mild soap water solution and
then rinse it in clean water. (4)
10.3.6 allow the filter to air dry before installing and using again.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business park ,
Bury st. Edmunds, suffolk,
Ip32 7aR
www.sealey.co.uk
Web
email
Symptom Possible causes Solutions
vacuum will not operate no power supply check power supply - cable, breakers, fuses.
Faulty power cable unplug and check the power cable. If
damaged have it replaced by your local sealey
dealer.
container full Empty container
dust expelled from the motor cover Cartridge filter missing or damaged Fit cartridge filter or replace damaged filter
Reduced efficiency and increased motor/
speed vibration
there is a blockage in the nozzle or hose
or in the container inlet.
Cartridge filter blocked by fine dust.
check nozzle, hose and container inlets and clear
any blockages found.
Remove filter and clean it or install new filter.