Husqvarna FSA 8400 D - Manual (Page 93)

93
FS6600 DIESEL - BLADE SIZE CONVERSION CHART
Note: Bladeshaft Spacers & V-Belt changes after Feb. 2005, S/N: 428033
10.27.05
Size To Convert To
Size To
Convert
From
36"
(900mm)
42"
(1000mm)
14”
(350mm)
&
18”
(450mm)
542 19 81-66 Blade Guard 3” Wide S/O
542 19 94-69 Bladeshaft Assy 36”
542 16 63-66 (2) Eng Pulley 8G 3.65” OD
Before Feb 2005:
542 19 95-02 (4) V-Belt 3VX435 4-Band
542 19 93-62 Blade Guard Attachment Kit
After Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
542 19 96-89 Blade Guard Attachment Kit
542 19 93-90 Blade Guard 4” Wide B/O
Note: Remove Slip-On Spades to allow attachment of 42”
Guard.
542 19 94-70 Bladeshaft Assy 42"
542 16 63-66 (2) Eng Pulley 8G 3.65" OD
Before Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
After Feb 2005:
542 19 97-64 (4) V-Belt 3VX485 4-Band
26"
(650mm)
542 19 81-66 Blade Guard 3” Wide S/O
542 19 94-69 Bladeshaft Assy 36”
542 16 63-66 (2) Eng Pulley 8G 3.65” OD
Before Feb 2005:
542 19 95-02 (4) V-Belt 3VX435 4-Band
542 19 93-62 Blade Guard Attachment Kit
After Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
542 19 96-89 Blade Guard Attachment Kit
542 19 93-90 Blade Guard 4” Wide B/O
Note: Remove Slip-On Spades to allow attachment of 42”
Guard.
542 19 94-70 Bladeshaft Assy 42"
542 16 63-66 (2) Eng Pulley 8G 3.65" OD
Before Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
After Feb 2005:
542 19 97-64 (4) V-Belt 3VX485 4-Band
30"
(750mm)
542 19 81-66 Blade Guard 3” Wide S/O
542 19 94-69 Bladeshaft Assy 36”
542 16 63-66 (2) Eng Pulley 8G 3.65” OD
Before Feb 2005:
542 19 95-02 (4) V-Belt 3VX435 4-Band
542 19 93-62 Blade Guard Attachment Kit
After Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
542 19 96-89 Blade Guard Attachment Kit
542 19 93-90 Blade Guard 4” Wide B/O
Note: Remove Slip-On Spades to allow attachment of 42”
Guard.
542 19 94-70 Bladeshaft Assy 42"
542 16 63-66 (2) Eng Pulley 8G 3.65" OD
Before Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
After Feb 2005:
542 19 97-64 (4) V-Belt 3VX485 4-Band
36"
(900mm)
No Conversion Required; configured:
- Blade Guard 3” Wide Slip-On – 36”
- (2) Spades & Spacers
- (2) Blade Shaft Pulley 8G3VX5.60” OD
- (2) Engine Pulley 8G3VX3.65” OD
- Flanges, 6.00” OD
Before Feb 2005:
542 19 95-02 (4) V-Belt 3VX435 4-Band
After Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
542 19 93-90 Blade Guard 4” Wide B/O
Note: Remove Slip-On Spades to allow attachment of 42”
Guard.
542 19 94-70 Bladeshaft Assy 42"
542 16 63-66 (2) Eng Pulley 8G 3.65" OD
Before Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
After Feb 2005:
542 19 97-64 (4) V-Belt 3VX485 4-Band
42"
(1000mm)
542 19 81-66 Blade Guard 3” Wide S/O
542 19 94-69 Bladeshaft Assy 36”
542 16 63-66 (2) Eng Pulley 8G 3.65” OD
Before Feb 2005:
542 19 95-02 (4) V-Belt 3VX435 4-Band
542 19 93-62 (2) Blade Guard Attachment Kit
After Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
542 19 96-89 (2) Blade Guard Attachment Kit
No Conversion Required; configured:
- Blade Guard 4” Wide Bolt-On – 42”
- Blade Guard Brace
- (2) Bladeshaft Pulley 8G3VX6.4" OD
- (2) Engine Pulley, 8G3VX3.65" OD
- Flanges, 7.00” OD
Before Feb 2005:
542 16 66-29 (4) V-Belt 3VX465 4-Band
After Feb 2005:
542 19 97-64 (4) V-Belt 3VX485 4-Band