Document Outline

• SITE ANALYZER™ XT
  • Safety Symbols
  • Warning Statements
  • Caution Statements
  • Safety Statements
  • Changes to this Manual
  • Definitions
  • Equations
    • Fault Location
      • Resolution
      • Maximum Distance
  • Chapter Layout
    • Table of Contents
• Chapter 1 Introduction
  • Items Supplied
    • Figure 1 Hardware and Software Supplied
  • Items Not Supplied
    • Figure 2 Hardware Not Supplied
  • Site Analyzer Features
    • General
    • Antenna Test
      • Measure Match Mode
      • Fault Location Mode
        • Transmitter Test
      • Measure Power Mode
        • Figure 3 Bird Power Sensors
        • Figure 4 Connector Diagram
  • Power Supply
    • Internal Battery
    • Adapters
    • External Battery Pack (Optional)
      • Figure 5 External Battery Pack
    • Charging the External Battery Pack
    • Using the External Battery Pack
  • Power Up
    • System Information
  • Site Analyzer User Keys
    • Figure 6 User Key Identification
  • Site Analyzer Display Screen
    • Display Description
      • Figure 7 Displays
• Chapter 2 Calibration
  • Calibration Accessories
  • Calibrating the Site Analyzer
    • Figure 8 Calibrating the Site Analyzer
• Chapter 3 Measure Match Mode
  • Determine the Power of the Component Being Tested
  • Selecting the Measure Match Mode
    • Figure 9 Selecting the Measure Match Mode
  • Setting the Measurement Frequency
    • Setting a Custom Sweep Frequency
      • Figure 10 Setting a Custom Sweep Frequency
    • Selecting a Sweep Frequency from a Band List
      • Figure 11 Selecting a Sweep Frequency from a Band List
  • Selecting the Measurement Units
    • Figure 12 Setting Match Mode Measurement Units
  • Setting the Measurement Scale Limits
    • Figure 13 Setting Match Mode Scale Limits
  • Setting the Measurement Data Points
    • Figure 14 Setting the Number of Measurement Data Points
  • Setting the Graph Display Type
    • Figure 15 Setting the Graph Display
  • Set and Activate Acceptance Limits
  • Measure the Match of the Component
  • Interpreting the Measurement
    • Figure 16 Measurement Screen
  • Cable Loss Measurement
    • Setting Up a Cable Loss Measurement
      • Figure 17 Set Up for Cable Loss Measurement
        • Performing a Cable Loss Measurement
    • Interpreting a Cable Loss Measurement
      • Figure 18 Cable Loss Measurement Screen
• Chapter 4 Fault Location Mode
  • Determine the Power of the Component Being Tested
  • Selecting Fault Location Mode
    • Figure 19 Select Fault Location Mode
  • Setting the Frequency Span and Max Distance
    • Figure 20 Setting the Frequency Span and the Center Frequency
  • Setting the Maximum Distance
    • Figure 21 Setting the Maximum Distance
    • Figure 22 Changed Max Distance Warning Message
  • Setting the Cable Type
    • Setting a Custom Cable Type
      • Figure 23 Setting a Custom Cable Type
    • Selecting a Cable Type from a Cable Type List
      • Figure 24 Selecting the Cable Type from List
  • Setting the Distance and Units
    • Setting the Start and Stop Distance
      • Figure 25 Setting the Start and Stop Distance
    • Setting the Distance Units
      • Figure 26 Setting the Distance Units
  • Setting the Scale & Unit of Measure
    • Setting Fault Location Scale Units
      • Figure 27 Setting Fault Location Scale Units
    • Setting Fault Location Scale Limits Manually
      • Figure 28 Setting Fault Location Scale Limits Manually
    • Setting Fault Location Auto Scale
      • Figure 29 Setting Fault Location Auto Scale
  • Set the Measurement Data Points
    • Setting the Measurement Resolution
      • Figure 30 Setting the Measurement Resolution
  • Set the Graph Display Type
    • Setting the Graph Display
      • Figure 31 Setting the Graph Display
  • Set and Activate Acceptance Limits
    • Figure 32 Setting a Limit Line
  • Test for Fault Location
  • Interpreting the Fault Location Measurement
    • Figure 33 Fault Location Measurement Screen
• Chapter 5 Power Measure Mode
  • Figure 34 Power Measure Mode
  • Figure 35 Connecting the SA to Measure Power
  • Connecting a Sensor
  • Display Description
    • Figure 36 Measure Power Screen Features
  • Setting the Full Scale Power
    • Figure 37 Full Scale Power Meter
  • Zeroing Bird Power Sensors
    • Figure 38 Zeroing, Message 1
    • Figure 39 Zeroing, Message 2
    • Figure 40 Zeroing, Power Meter
  • Choosing the Displayed Measurement
    • Figure 41 Match Screen
  • Setting Units
    • Figure 42 Forward Screen
  • Changing the Mode for the Directional Power Sensor
    • Figure 43 DPS, Forward Screen
    • The 43 Peak Mode
      • Figure 44 DPS, Match Screen
  • Recall Setups
    • Figure 45 Setup Screens
• Chapter 6 General Operation
  • Setting a Limit Line
    • Figure 46 Setting a Limit Line
  • Measurement Hold
    • Figure 47 Measurement Hold
    • Activate Markers and Set Marker Style
      • Figure 48 Activate Marker and Set Style
    • Move Markers
    • Moving Markers
      • Figure 49 Moving Markers
    • Using Delta Markers
      • Figure 50 Delta Markers
    • Using Markers with Recalled Traces
      • Figure 51 Using Markers with Recalled Traces
  • Setting Display Smoothing
    • Figure 52 Setting Display Smoothing
    • Figure 53 Display with High Smoothing Selected
  • Saving and Recalling Traces
    • Figure 54 Out of Memory Message
    • Connecting a USB Flash Drive
    • Saving a Trace
      • Figure 55 Save Trace Screen
      • Figure 56 Text Label Screen
    • Recalling a Saved Trace
      • Figure 57 Selecting and Recalling a Saved Trace
    • Viewing a Recalled Trace
      • Figure 58 Comparing Data Points in Dual Mode
    • Deleting a Saved Trace
      • Figure 59 Selecting and Deleting a Saved Trace
  • Instrument Setups
    • Saving a Setup
    • Figure 60 Saving a Setup
    • Recalling a Saved Setup
      • Figure 61 Recalling a Saved Setup
    • Deleting a Saved Setup
      • Figure 62 Deleting a Saved Setup
  • Label Text
    • Label Text Shortcuts
      • Figure 63 Text Label Configuration
    • Label Text Help
      • Figure 64 Text Label Help
    • Editing Label Text
      • Figure 65 Editing Label Text
  • Quicktext for Trace Labels
    • Adding Quicktext Elements
      • Figure 66 Adding the Edit Line Text
    • Using Quicktext
      • Figure 67 Inserting Quicktext Elements
    • Deleting Quicktext Elements
      • Figure 68 Selecting and Deleting Quicktext Elements
• Chapter 7 Utilities
  • Figure 69 Utility Screen
  • Adjust Date and Time
    • Figure 70 System Settings Screen
    • Figure 71 Date Screen
  • Return to Defaults
    • Figure 72 Defaults Option Screen
  • FM Modulation
    • Figure 73 FM Modulation Screen
• Chapter 8 Computer Software
  • Features
  • Computer Requirements
• Chapter 9 Maintenance
  • Cleaning
  • Charging the Battery
  • External Battery Pack (Optional), Long-term Storage Maintenance
  • Troubleshooting
  • Replacing the Battery
    • Figure 74 Replacing the Battery
  • Customer Service
  • Specifications
    • Antenna Testing
      • Measurement Accuracy (after 1 display refresh)
    • Match Measurement
    • Distance to Fault (DTF) Measurement
      • Power Measure Mode
    • General
      • Figure 75 Measurement Uncertainty (Return Loss after one refresh)
  • Parts List
  • Optional Equipment Available
    • Precision Adapters
    • Armored (Phase Stable) Test Cables
    • Precision Open/Short/Load Combinations
    • Accessories
    • Power Sensors Supported
    • Appendix
  • Fault Location Distance Tables
    • Fault Location Distance - 238 Data Points
    • Fault Location Distance - 475 Data Points
    • Fault Location Distance - 949 Data Points
      • Limited Warranty