Document Outline

• RabbitCore RCM4000 User's Manual
  • Table of Contents
  • 1. Introduction
    • 1.1 RCM4000 Features
    • 1.2 Advantages of the RCM4000
    • 1.3 Development and Evaluation Tools
      • 1.3.1 RCM4000 Development Kit
      • 1.3.2 Software
      • 1.3.3 Online Documentation
  • 2. Getting Started
    • 2.1 Install Dynamic C
    • 2.2 Hardware Connections
      • 2.2.1 Prepare the Prototyping Board for Development
      • 2.2.2 Attach Module to PrototypingBoard
      • 2.2.3 Connect Programming Cable
      • 2.2.4 Connect Power
    • 2.3 Run a Sample Program
      • 2.3.1 Run a Sample Program
      • 2.3.2 Troubleshooting
    • 2.4 Where Do I Go From Here?
      • 2.4.1 Technical Support
  • 3. Running Sample Programs
    • 3.1 Introduction
    • 3.2 Sample Programs
      • 3.2.1 Use of NAND Flash (RCM4000 only)
      • 3.2.2 Serial Communication
      • 3.2.3 A/D Converter Inputs (RCM4000 only)
      • 3.2.4 Real-Time Clock
  • 4. Hardware Reference
    • 4.1 RCM4000 Digital Inputs and Outputs
      • 4.1.1 Memory I/O Interface
      • 4.1.2 Other Inputs and Outputs
    • 4.2 Serial Communication
      • 4.2.1 Serial Ports
      • 4.2.2 Ethernet Port
      • 4.2.3 Programming Port
    • 4.3 Programming Cable
      • 4.3.1 Changing Between Program Mode and Run Mode
      • 4.3.2 Standalone Operation of the RCM4000
    • 4.4 A/D Converter (RCM4000 only)
      • 4.4.1 A/D Converter Power Supply
    • 4.5 Other Hardware
      • 4.5.1 Clock Doubler
      • 4.5.2 Spectrum Spreader
    • 4.6 Memory
      • 4.6.1 SRAM
      • 4.6.2 Flash EPROM
      • 4.6.3 NAND Flash
  • 5. Software Reference
    • 5.1 More About Dynamic C
    • 5.2 Dynamic C Function Calls
      • 5.2.1 Digital I/O
      • 5.2.2 Serial Communication Drivers
      • 5.2.3 SRAM Use
      • 5.2.4 Prototyping Board Functions
      • 5.2.5 Analog Inputs (RCM4000 only)
    • 5.3 Upgrading Dynamic C
      • 5.3.1 Add-On Modules
  • 6. Using the TCP/IP Features
    • 6.1 TCP/IP Connections
    • 6.2 TCP/IP Primer on IP Addresses
      • 6.2.1 IP Addresses Explained
      • 6.2.2 How IP Addresses are Used
      • 6.2.3 Dynamically Assigned Internet Addresses
    • 6.3 Placing Your Device on the Network
    • 6.4 Running TCP/IP Sample Programs
      • 6.4.1 How to Set IP Addresses in the Sample Programs
      • 6.4.2 How to Set Up your Computer for Direct Connect
    • 6.5 Run the PINGME.C Sample Program
    • 6.6 Running Additional Sample Programs With Direct Connect
    • 6.7 Where Do I Go From Here?
  • Appendix A. RCM4000 Specifications
    • A.1 Electrical and Mechanical Characteristics
      • A.1.1 A/D Converter
      • A.1.2 Headers
    • A.2 Rabbit 4000 DC Characteristics
    • A.3 I/O Buffer Sourcing and Sinking Limit
    • A.4 Bus Loading
    • A.5 Conformal Coating
    • A.6 Jumper Configurations
  • Appendix B. Prototyping Board
    • B.1 Introduction
      • B.1.1 Prototyping Board Features
    • B.2 Mechanical Dimensions and Layout
    • B.3 Power Supply
    • B.4 Using the Prototyping Board
      • B.4.1 Adding Other Components
      • B.4.2 Measuring Current Draw
      • B.4.3 Analog Features (RCM4000 only)
      • B.4.4 Serial Communication
    • B.5 Prototyping Board Jumper Configurations
  • Appendix C. Power Supply
    • C.1 Power Supplies
      • C.1.1 Battery-Backup Circuits
      • C.1.2 Reset Generator
  • Notice to Users
  • Index
  • Schematics