3 development and evaluation tools, 1 rcm4000 development kit, Dynamic c – Digi RCM4000 User Manual
Page 10: Pin header to db9 serial cable, Ac adapter, U1 c1 gnd c2, Bt1 1, Rx81, Rx83 rx11, Rx67
4
RabbitCore RCM4000
1.3 Development and Evaluation Tools
1.3.1 RCM4000 Development Kit
The RCM4000 Development Kit contains the hardware essentials you will need to use
your RCM4000 module. The items in the Development Kit and their use are as follows.
•
RCM4010 module.
•
Prototyping Board.
•
AC adapter, 12 V DC, 1 A. (Included only with Development Kits sold for the North
American market. A header plug leading to bare leads is provided to allow overseas
users to connect their own power supply with a DC output of 8–24 V at 8 W.)
•
10-pin header to DE9 programming cable with integrated level-matching circuitry.
•
10-pin header to DB9 serial cable.
•
Dynamic C
®
CD-ROM, with complete product documentation on disk.
•
Getting Started instructions.
•
A bag of accessory parts for use on the Prototyping Board.
•
Rabbit 4000 Processor Easy Reference poster.
•
Registration card.
Figure 1. RCM4000 Development Kit
®
A Digi International® Company.
Rabbit Semiconductor, Rabbit, Z-World, and Dynamic C are
registered trademarks of their respective holders.
RabbitCore RCM4000
Getting Started
Development Kit Contents
The RCM4000 Development Kit contains the following items:
• RCM4000 module.
• Prototyping Board.
• AC adapter, 12 V DC, 1 A. (Included only with Development Kits sold for the North American market. A
header plug leading to bare leads is provided to allow overseas users to connect their own power supply
with a DC output of 8–30 V.)
• 10-pin header to DB9 programming cable with integrated level-matching circuitry.
• 10-pin header to DB9 serial cable.
• Dynamic C® CD-ROM, with complete product documen-
tation on disk.
• Getting Started instructions.
• A bag of accessory parts for use on the Prototyping
Board.
• Rabbit 4000 Processor Easy Reference poster.
• Registration card.
Installing Dynamic C
®
Insert the CD from the Development Kit in
your PC’s CD-ROM drive. If the installation
does not auto-start, run the setup.exe
program in the root directory of the
Dynamic C CD. Install any Dynamic C
modules after you install Dynamic C.
PROG
DIAG
Programming
Cable
Getting Started
Instructions
Prototyping Board
Accessory Parts for
Prototyping Board
Serial
Cable
D1
R1
PWR
DS1
GND
J1
U1
C1
GND
C2
JP
1
C3
D2
JP
2
C4
+3
.3
V
J2
R2
BT1
1
S1
RESET
RX
D T
XD
TX
C
RX
C
GN
D
J4
UX
29
RX81
RX
87
CX
41
RX83
RX11
CX
39
UX30
UX10
UX12
UX14
UX16
RX79
CX
29
CX
17
RX67
UX
45
RX
85
GND
GND
GND
1
R24
R22
R21
R23
CX23 RX77
1
R2
7
R2
8
JP25
CX25
RX75
RX73
CX27
DS3
S3
S2
DS2
J3
UX49
UX4
UX47
+5 V
GND
+3.3 V
RCM1
U2
/RST_OUT
/IOWR
VBAT
EXT
PA1
PA3
PA5
PA7
PB1
PB3
PB5
PB7
PC1
PC3
PC5
PC7
PE1
PE3
PE5
PE7
PD1
LN1
PD3
LN3
PD5
LN5
PD7
LN7
VREF
GND
/IORD
/RST_IN
PA0
PA2
PA4
PA6
PB0
PB2
PB4
PB6
PC0
PC2
PC4
PC6
PE0
PE2
PE4
PE6
PD0
LN0
PD2
LN2
PD4
LN4
PD6
LN6
CVT
AGND
JP
24
JP
23 C1
4
C1
2
C1
0 C8 C7 C9 C11 C13
R10
R8 R6 R4 R3 R5 R7
R20
R1
8
R1
6
R1
4
R1
3
R1
5
R1
7
R29
JP
11
JP
15
JP
19
JP
21
JP2
2
JP2
0
JP1
7
JP
13
R19
R9
RX57
RX55
RX97
RX49
UX
33
UX
31
RX
89
UX3
UX
37
UX
42
UX
41
RX
63
RX
65
RX
61
RX59
R2
6
R25
Q1
C15
C1
9
C2
0
U3
C18
C1
7
JP16
JP6
JP5
JP12
JP4
JP3
JP14
JP8
JP7
JP18
JP9
JP10
C16
L1C6
C5
AG
ND CVT LN6I
N
LN
4IN
LN
2IN
LN
0IN
VR
EF
LN
7IN
LN
5IN
LN
3IN
LN
1IN
AG
ND
AG
ND
R1
1
R1
2
RX
47
RX43
AC Adapter
(North American
kits only)
C20
L1
C21
R5
R6
R7
R8
R9
R10
R11
R12
R13
C9
C10
C11
C12
C13
C14
C15
C16
RP1
JP6
JP5
R20
JP4
C3
U4
TP2
J1
R38
R2
R1
U1
C8
C1
U2
C5
C4
R3 U3
R37
R21
U5
C17
C18
C52
C56
R23
R22
U6
JP3
R41
C6 C7 R4
U9
C53
1
40
41
80