Document Outline

• 1. INTRODUCTION
  • OEM Installations
  • Warning
  • About this Guide
  • Menu Descriptions
• 2. WIRING OVERVIEW
  • Recommended Wiring Practices
  • Power Requirements
  • 25-Pin Female EFIS Harness
    • WIRING SYSTEM OVERVIEW
• 3. INSTRUMENT INSTALLATION
  • Selecting a Remote Compass Module Location
  • EDC-D10A Communication Cable
  • Power Inputs
  • Serial Communication Cable
    • PC USB CONNECTION
    • EFIS SERIAL HARNESS
  • SL30 and/or GPS connection
    • IF YOU OWN ONLY AN EFIS-D10A OR EFIS-D100
    • IF YOU OWN TWO EFIS-ONLY UNITS
    • IF YOU OWN ONLY AN EMS-D10 OR EMS-D120
    • IF YOU OWN AN EMS AND AN EFIS (NOT FLIGHTDEK-D180)
    • IF YOU OWN ONLY A FLIGHTDEK-D180
    • IF YOU OWN A FLIGHTDEK-D180 AND AN EFIS
  • Altitude Encoder Wiring
    • SERIAL ALTITUDE FORMATS
      • Format 1
      • Format 2
      • Format 3
      • Format 4
  • Audio Alert Output
  • Dynon Smart Avionics Bus (DSAB) Wiring
  • Panel Location and Mounting
  • Connecting Static & Pitot Lines
• 4. EFIS CALIBRATION AND CONFIGURATION
  • Ensuring Proper Installation
  • Setting Zero Pitch (In flight)
  • Compass Heading Calibration
    • SETTING MAGNETIC INCLINATION ANGLE AND INTENSITY (REQUIRED)
      • Obtaining Magnetic Inclination and Intensity
      • Entering inclination and intensity into the EFIS-D100
    • EDC-D10A HEADING CALIBRATION (ON GROUND ONLY)
      • Troubleshooting
  • Configure Airspeed Color Thresholds
• 5. DSAB CONFIGURATION
  • Network Concepts
  • Example Networks
  • Initial Setup
  • Brightness Configuration
  • Network Status
• 6. AUTOPILOT INSTALLATION AND CONFIGURATION
  • Additional Information and Updates
  • DSAB Firmware Compatibility
  • Compass Calibration Critical For Certain AP Modes
  • Autopilot System Electrical Installation
    • SERVO ELECTRICAL INSTALLATION
    • AP CONTROLS ELECTRICAL INSTALLATION
    • AP74 ELECTRICAL INSTALLATION
  • Servo Mechanical Installation
    • SERVO DIMENSIONS
    • LINKAGE MOUNT POSITION FORCE AND TRAVEL
  • AP74 Mechanical Installation
    • AP74 DIMENSIONS AND PANEL LOCATION
    • MOUNTING BRACKET DIMENSIONS
    • AP74 MOUNTING
  • Firmware Upgrades Required For AP Functionality
  • AP Servo Configuration
    • CONFIGURATION OVERVIEW
    • STEP 1 - CONFIGURE DSAB
    • STEP 2 - SERVO CALIBRATION AND SERVO TEST
    • STEP 3 - ROLL SERVO INITIAL SETUP
    • STEP 4 – PITCH SERVO INITIAL SETUP
      • Advanced Pitch Gain and Rate Adjustments
    • STEP 5 – DISENGAGE/CWS BUTTON CONFIGURATION
    • STEP 6 - AUDIO ALERTS CONFIGURATION
    • STEP 7 – PREPARE FOR FLIGHT TEST ON CLEAR, VFR DAY
    • STEP 8 – ROLL SERVO FLIGHT TUNING
    • STEP 9 – PITCH SERVO FLIGHT TUNING
    • STEP 10 – VERIFY OVERALL AP PERFORMANCE
  • AP74 Configuration
    • VALUE KNOB CONFIGURATION
    • PRE-SELECT CONFIGURATION
    • MODE CLEARING CONFIGURATION
• 7. APPENDIX
  • Appendix A: Ongoing Maintenance and Troubleshooting
    • INTRODUCTION
    • CAUTION
    • INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
    • AP SERVO INSTALLATION
    • ALTIMETER CHECK
    • INTERNAL BATTERY CHECK
    • FIRMWARE UPGRADE
    • DISPLAYED ALERT MESSAGES
    • TROUBLESHOOTING GUIDE
    • INSTRUCTIONS FOR RETURN
  • Appendix B: Dynon OAT Probe Installation and Usage
    • TOOLS AND MATERIALS REQUIRED
    • INSTALLATION
      • Mount Location
      • Mounting Instructions
      • Wiring Instructions.
    • OAT/TAS/DA DISPLAY
    • CALIBRATION AND ADJUSTMENT
    • TROUBLESHOOTING
      • OAT value fluctuates wildly
      • OAT value is consistently high/low
      • OAT display area states OAT NOT FOUND
      • Other strange behavior by OAT reading
  • Appendix C: HS34 Installation and Configuration
    • WIRING
      • Harness Construction
      • Power Requirements
      • Connector Description
      • Pinouts and Function Description
      • Universal Connections
      • Generic Device Connections
      • Common Device Connections
    • PANEL LOCATION AND MOUNTING
      • HS34 Dimensions and Panel Location
      • Mounting Tab Dimensions
      • HS34 Mounting
    • HS34 CONFIGURATION
      • Device Communication Setup
      • Markers Configuration
      • DME Configuration
      • GPS and NAV Display Order Configuration
      • Voice/Tone Alert Configuration
      • VALUE Knob Configuration
      • NAV and/or GPS Fail-over
  • Appendix D: Dynon AOA/Pitot Installation and Calibration
    • AOA CALCULATION: PRINCIPLES OF OPERATION
    • HEATING: PRINCIPLES OF OPERATION
    • FAILURE WARNING
    • TOOLS AND MATERIALS REQUIRED
    • HEATER CONTROLLER WIRING AND MOUNTING
      • Heater Controller Mounting
      • Heated AOA/Pitot Wiring System Overview
      • Heater Controller Wiring
      • Probe to Controller Wiring
      • Controller Power wiring
      • Heater Status Connection
    • AOA/PITOT PROBE MOUNTING
      • AOA/Pitot Probe Mount Location
      • AOA/Pitot Probe Mounting Instructions
    • DIMENSIONS
      • Standard mount
      • Boom mount
    • PLUMBING
    • PRESSURE CHECK
    • CALIBRATION
    • ALARM SETUP
  • Appendix E: Encoder Serial-to-Gray Code Converter Installation
    • INTRODUCTION AND DESCRIPTION
    • TOOLS AND EQUIPMENT
    • ELECTRICAL INSTALLATION
    • RECOMMENDED WIRING PRACTICES
    • STEP 1: TRANSPONDER WIRING
    • STEP 2: CONNECTING TO THE EFIS-D100
    • STEP 3: EFIS-D100 ENCODER FORMAT
  • Appendix F: Replacing the EFIS-D100 battery pack
  • Appendix G: Weights
  • Appendix H: EFIS-D100 Specifications