Document Outline

• Table Of Contents
• Tables
• Figures
• About This Manual
• 1. Introduction
  • 1.1 PRODUCT OVERVIEW
  • 1.2 SPECIFICATIONS
    • 1.2.1 GENERAL SPECIFICATIONS
    • 1.2.2 PRESSURE MEASUREMENT SPECIFICATIONS
      • 1.2.2.1 QUARTZ REFERENCE PRESSURE TRANSDUCERS (Q-RPT)
      • 1.2.2.2 ON-BOARD BAROMETER
• 2. Installation
  • 2.1 UNPACKING AND INSPECTION
    • 2.1.1 REMOVING FROM PACKAGING
    • 2.1.2 INSPECTING CONTENTS
  • 2.2 PGC-10000-AF SYSTEM
  • 2.3 SITE REQUIREMENTS
  • 2.4 SETUP
    • 2.4.1 PREPARING FOR OPERATION
    • 2.4.2 RPM4/HPMS FRONT, REAR AND SIDE VIEWS
      • 2.4.2.1 RPM4/HPMS FRONT VIEW
      • 2.4.2.2 RPM4/HPMS REAR VIEW
      • 2.4.2.3 RPM4/HPMS SIDE VIEW
    • 2.4.3 RPM4 FRONT AND REAR PANELS
      • 2.4.3.1 RPM4 FRONT PANEL
      • 2.4.3.2 RPM4 REAR PANEL
    • 2.4.4 POWER CONNECTION
    • 2.4.5 FOOTSWITCH CONNECTION
    • 2.4.6 TEST PORT CONNECTION
      • 2.4.6.1 THE ATM PORTS OF RPM4
    • 2.4.7 CHECK/SET SECURITY LEVEL
    • 2.4.8 SETTING UP AUTOTEST FILES
  • 2.5 POWER-UP AND VERIFICATION
    • 2.5.1 SWITCH POWER ON
    • 2.5.2 CHECK PRESSURE MEASUREMENT OPERATION
      • 2.5.2.1 CHECKING ABSOLUTE MODE PRESSURE MEASUREMENT
      • 2.5.2.2 CHECKING GAUGE MODE PRESSURE MEASUREMENT
  • 2.6 SHORT TERM STORAGE
  • 2.7 LONG TERM STORAGE AND/OR PREPARATION FOR SHIPPING
• 3. Operation
  • 3.1 USER INTERFACE
    • 3.1.1 MAIN RUN SCREEN
    • 3.1.2 FUNCTION / DATA KEYPAD LAYOUT AND PROTOCOL
    • 3.1.3 REMOTE [ENT] (ENTER) FOOTSWITCH
    • 3.1.4 SOUNDS
  • 3.2 GENERAL OPERATING PRINCIPLES
    • 3.2.1 PRESSURE READY/NOT READY
    • 3.2.2 GAUGE MODE, DYNAMIC COMPENSATION FOR ATMOSPHERIC PRESSURE
    • 3.2.3 MULTIPE RANGES (Q-RPTS, AUTORANGE AND INFINITE RANGING)
    • 3.2.4 AUTOMATED TEST AND CALIBRATION SEQUENCES
    • 3.2.5 HPMS (HIGH PRESSURE MOUNTING SYSTEM)
    • 3.2.6 DIRECT FUNCTION KEYS SUMMARY
  • 3.3 DIRECT FUNCTION KEYS
    • 3.3.1 [RANGE]
    • 3.3.2 [UNIT]
    • 3.3.3 [MODE]
    • 3.3.4 [AutoRange]
    • 3.3.5 [LEAK CK]
    • 3.3.6 [DISPLAY]
      • 3.3.6.1 AVG (AVERAGE)
      • 3.3.6.2 Rate
      • 3.3.6.3 Dev (Deviation)
      • 3.3.6.4 RPT
      • 3.3.6.5 Hi/Lo
      • 3.3.6.6 Freeze
      • 3.3.6.7 Clean
    • 3.3.7 [HEAD]
    • 3.3.8 [SDS]
    • 3.3.9 [AutoZ]
      • 3.3.9.1 [AUTOZ] IN GAUGE MODE
      • 3.3.9.2 [AUTOZ] IN ABSOLUTE MODE
    • 3.3.10 [ENT] (RUN AUTOTEST)
      • 3.3.10.1 AUTOTEST INITIALIZATION
      • 3.3.10.2 TEST EXECUTION
  • 3.4 [SETUP]
    • 3.4.1 <1RANGE>
      • 3.4.1.1 SAVING AN AutoRange RANGE
      • 3.4.1.2 DELETING AutoRange RANGES
    • 3.4.2 <2RES> (RESOLUTION)
    • 3.4.3 <3STAB>
    • 3.4.4 <4UL> (UPPER LIMIT)
      • 3.4.4.1 OVER PRESSURE FUNCTION
    • 3.4.5 <5ATest>
      • 3.4.5.1 DATA
      • 3.4.5.2 FILE
  • 3.5 [SPECIAL]
    • 3.5.1 <1AutoZ>
      • 3.5.1.1 EDIT AUTOZ
    • 3.5.2 <2REMOTE>
      • 3.5.2.1 <1COM1, 2COM2>
      • 3.5.2.2 <3IEEE-488>
      • 3.5.2.3 <4FORMAT>
      • 3.5.2.4 <5RS232 SELF-TEST>
    • 3.5.3 <3HEAD>
    • 3.5.4 <4SDS>
    • 3.5.5 <5PREFS>
      • 3.5.5.1 <1ScrSvr>
      • 3.5.5.2 <2SOUND>
      • 3.5.5.3 <3TIME>
      • 3.5.5.4 <4ID>
      • 3.5.5.5 <5LEVEL> (SECURITY)
    • 3.5.6 <6PUNIT>
    • 3.5.7 <7INTERNAL>
      • 3.5.7.1 <1BARO>
      • 3.5.7.2 <2ReadRt>
      • 3.5.7.3 <3RPT2x>
      • 3.5.7.4 <4LO VNT>
      • 3.5.7.5 <5LOG>
    • 3.5.8 <8CAL>
    • 3.5.9 <9RESET>
      • 3.5.9.1 <1SETS>
      • 3.5.9.2 <2 UNITS>
      • 3.5.9.3 <3ATest>
      • 3.5.9.4 <4 CAL>
      • 3.5.9.5 <5 ALL>
• 4. Remote Operation
  • 4.1 OVERVIEW
  • 4.2 INTERFACING
    • 4.2.1 RS232 INTERFACE
      • 4.2.1.1 COM1
      • 4.2.1.2 IEEE-488
      • 4.2.1.3 COM2
  • 4.3 PROGRAMMING FORMATS
    • 4.3.1 CLASSIC PROGRAM MESSAGE FORMAT
    • 4.3.2 ENHANCED PROGRAM MESSAGE FORMAT
      • 4.3.2.1 USING COMMAND TYPE COMMANDS
      • 4.3.2.2 USING QUERY TYPE COMMANDS
  • 4.4 COMMANDS
    • 4.4.1 PROGRAMMING MESSAGES
    • 4.4.2 ERROR MESSAGESS
    • 4.4.3 PROGRAM MESSAGE DESCRIPTION OVERVIEW
    • 4.4.4 PROGRAM MESSAGE DESCRIPTIONS
  • 4.5 STATUS REPORTING SYSTEM
    • 4.5.1 ERROR QUEUE
    • 4.5.2 STATUS BYTE REGISTER
    • 4.5.3 STANDARD EVENT REGISTER
    • 4.5.4 READY STATUS REGISTER
  • 4.6 IEEE STD. 488.2 COMMON AND STATUS PROGRAM MESSAGES
    • 4.6.1 PROGRAM MESSAGE DESCRIPTIONS
• 5. Maintenance, Adjustments and Calibration
  • 5.1 OVERVIEW
  • 5.2 RPM4 MAINTENANCE
    • 5.2.1 AUTOZERO OF Q-RPTS
      • 5.2.1.1 GAUGE MODE AUTOZERO
      • 5.2.1.2 ABSOLUTE MODE AUTOZERO
    • 5.2.2 ADJUSTMENT OF THE ON-BOARD BAROMETER
  • 5.3 RPM4 Q-RPT CALIBRATION
    • 5.3.1 PRINCIPLE
      • 5.3.1.1 PA AND PM COEFFICIENTS
      • 5.3.1.2 AS RECEIVED AND AS LEFT DATA
    • 5.3.2 EQUIPMENT REQUIRED
    • 5.3.3 SET-UP AND PREPARATION
    • 5.3.4 RECOMMENDED CALIBRATION POINT SEQUENCE
    • 5.3.5 TURNING OFF ABSOLUTE MODE CAPABILITY FOR A Q-RPT
    • 5.3.6 Q-RPT CALIBRATION USING CALTOOL FOR Q-RPTS SOFTWARE
    • 5.3.7 EDITING AND VIEWING Q-RPT CALIBRATION INFORMATION
    • 5.3.8 Q-RPT ADJUSTMENT WITHOUT CALTOOL FOR Q-RPTS SOFTWARE
  • 5.4 RPM4 REPAIR
    • 5.4.1 REMOVING RPM4 FROM HPMS
    • 5.4.2 OPENING AND CLOSING THE RPM4 ENCLOSURE
    • 5.4.3 RELOADING EMBEDDED SOFTWARE INTO FLASH MEMORY
    • 5.4.4 SUBASSEMBLY DESCRIPTION AND LOCATION
      • 5.4.4.1 MICRO BOARD
      • 5.4.4.2 POWER SUPPLY MODULE
      • 5.4.4.3 DRIVER BOARD
      • 5.4.4.4 ON-BOARD BAROMETER
      • 5.4.4.5 Q-RPT MODULE
      • 5.4.4.6 DISPLAY
      • 5.4.4.7 COOLING FAN
    • 5.4.5 Q-RPT MODULE PNEUMATIC SCHEMATIC
  • 5.5 RPM4 ILLUSTRATED PARTS BREAKDOWN
  • 5.6 HPMS MAINTENANCE
    • 5.6.1 HPMS OVERHAUL
  • 5.7 HPMS ILLUSTRATED PARTS BREAKDOWN
• 6. Troubleshooting
• 7. Appendix
  • 7.1 UNIT CONVERSION
    • 7.1.1 PRESSURE
• 8. Warranty
  • 8.1 OVERVIEW
• 9. Glossary