Great Plains EWNT7 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for EWNT7 Great Plains
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 14 |
| Size: | 819 KB |
Show table of contents
Read manual
Document Outline
- Introduction
- 1. 123-832H Slotted Idler Arm 1/2" x 2 13/16"
- 2. 152-143H 7' Clutch Rod
- 3. 152-144H 7' Clutch Rod Support
- 4. 152-145H 7' Clutch Link Pull Arm
- 5. 152-147H 7' & 10' Clutch Rod Push Arm
- 6. 152-149H 7' & 10' Clutch Arm Seed Only
- 7. 152-305D 7' & 10' Clutch Tab Adjust
- 8. 152-306D Clutch Rod Pivot Bushing
- 9. 152-308D Clutch Rod Spacer
- 10. 152-262D Clutch Engage Arm
- 11. 802-017C Bolt, Hex Head 3/8"-16 x 1" Long
- 12. 802-079C Bolt, Hex Head 3/8"-16 x 1 1/4" Long
- 13. 802-159C Bolt, Hex Head 5/16"-18 x 1" Long
- 14. 803-008C Nut, Hex 5/16"-18
- 15. 803-013C Nut, Lock 3/8"-16
- 16. 803-014C Nut, Hex 3/8"-16
- 17. 803-078C Nut, Lock 3/8"-16 Nylon Insert
- 18. 804-009C Washer, Lock Spring 5/16"
- 19. 804-010C Washer, Flat 5/16" USS
- 20. 804-012C Washer, Flat 3/8" SAE
- 21. 804-013C Washer, Lock Spring 3/8"
- 22. 804-031C Washer, Retaining
- 23. 805-019C Pin, Cotter 5/32" x 1" Long
- Using this Manual
- Assembly
- New 7’ End Wheel No-Till Clutch Linkage Assembly
- Figure 2-3
- New 10’ End Wheel No-Till Clutch Linkage Assembly
- Figure 2-6
- 1. 152-146H 10' Clutch Link Pull Arm
- 2. 152-147H 7' & 10' Clutch Rod Push Arm
- 3. 152-149H 7' & 10' Clutch Arm Seed Only
- 4. 152-150H 10' Clutch Rod
- 5. 152-297D 10' Clutch Rod Support Mount
- 6. 152-305D 7' & 10' Clutch Tab Adjust
- 7. 152-306D Clutch Rod Pivot Bushing
- 8. 152-307D 10' Clutch Tab Adj Mount
- 9. 152-308D Clutch Rod Spacer
- 10. 152-262D Clutch Engage Arm
- 11. 802-017C Bolt, Hex Head 3/8"-16 x 1" Long
- 12. 802-079C Bolt, Hex Head 3/8"-16 x 1 1/4" Long
- 13. 802-159C Bolt, Hex Head 5/16"-18 x 1" Long
- 14. 803-008C Nut, Hex 5/16"-18
- 15. 803-013C Nut,Lock 3/8"-16
- 16. 803-014C Nut, Hex 3/8"-16
- 17. 803-078C Nut, Lock 3/8"-16 Nylon Insert
- 18. 804-009C Washer, Lock Spring 5/16"
- 19. 804-012C Washer, Flat 3/8" SAE
- 20. 804-013C Washer, Lock Spring 3/8"
- 21. 804-031C Washer, Retaining
- 22. 804-036C Washer, Flat 5/16" SAE
- 23. 805-019C Pin, Cotter 5/32" x 1" Long
- Torque Values Chart for Common Bolt Sizes
- Section 2 Assembly & Set-Up
- Clutch Linkage
- 7’ & 10’ End Wheel No-Till
- General Information
- Table of Contents
- General Operation & Repair
- 1. DO NOT exceed 20 mph transport speed.
- 2. Areas of this drill can be dangerous and can cause bodily harm if not properly used or guarded. Stay away from equipment when it is in operation!
- 3. Before working on, servicing or making adjustments on the drill, ALWAYS disengage power, shut off engine, make sure all moving parts have stopped, and all pressure in the system is relieved.
- 4. Escaping fluid under pressure can have sufficient force to penetrate the skin. Check all hydraulic lines and hoses before app...
- General Operation & Repair
- Section 1 Safety Rules
- 7’ & 10’ End Wheel No-Till