HP ProLiant DL385 Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for ProLiant DL385 HP
Manuals
Read manual
| Recognized languages: | English |
|---|---|
| Pages: | 47 |
| Size: | 278 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 174 |
| Size: | 7.08 MB |
Show table of contents
Read manual
Document Outline
- HP ProLiant DL385 Server User Guide
- Notice
- Contents
- Server component identification
- Front panel components
- Front panel LEDs and buttons
- Rear panel components
- Rear panel LEDs and buttons
- System board components
- SCSI backplane components
- SAS backplane components
- System board LEDs
- System LEDs and internal health LED combinations
- SCSI backplane LEDs
- Hot-plug SCSI hard drive LEDs
- Hot-plug SCSI hard drive LED combinations
- Hot-plug SAS hard drive LEDs
- Hot-plug SAS hard drive LED combinations
- PCI riser cage LED
- Remote management connector
- Identifying hot-plug fans
- Hot-plug fan LED
- Power converter module LED
- Battery-backed write cache LEDs
- Battery-backed write cache LED statuses
- Server operations
- Server setup
- Optional installation services
- Rack planning resources
- Optimum environment
- Rack warnings
- Identifying the contents of the server shipping carton
- Installing hardware options
- Installing the server into the rack
- Powering up and configuring the server
- Installing the operating system
- Registering the server
- Hardware options installation
- Introduction
- Processor option
- Memory options
- Hot-plug SCSI hard drive options
- Power supply blank
- Hot-plug SAS hard drive options
- Installing a diskette drive
- Hot-plug tape drive option
- Redundant hot-plug fans
- Battery-backed write cache option
- Redundant hot-plug AC power supply option
- Expansion board options
- Server cabling
- Cabling
- SAS model cabling
- SCSI model cabling
- Embedded simplex SCSI cabling
- Embedded duplex SCSI cabling
- PCI simplex SCSI cabling
- PCI duplex SCSI cabling
- Mixed duplex SCSI cabling
- Installing the SCSI terminator board
- Removing the SCSI terminator board
- USB cabling
- DVD/CD-ROM drive cabling
- Diskette drive cabling
- Power button/LED cabling
- RILOE cabling (SCSI)
- Internal power cabling
- Server software and configuration utilities
- Configuration tools
- Management tools
- Diagnostic tools
- Keeping the system current
- Battery replacement
- Troubleshooting
- Troubleshooting resources
- Server diagnostic steps
- Important safety information
- Preparing the server for diagnosis
- Symptom information
- Service notifications
- Loose connections
- Diagnostic steps
- POST error messages and beep codes
- Introduction to POST error messages
- Invalid memory types were found on the same node. Please check DIMM compatibility. - Some DIMMs may not be used
- Node Interleaving disabled - Invalid memory configuration
- Processor Reduced Power Mode Enabled in RBSU
- Processor Not Started (Processor Stalled)
- Processor Not Started (Stepping Does Not Match)
- Processor Not Started (Unsupported Processor Stepping)
- Processor Not Supported (Unsupported Core Speed)
- There must be a first DIMM in pair if second DIMM in pair is populated. Second DIMM in pair ignored.
- Unsupported DIMM(s) found in system. - DIMM(s) may not be used
- Unsupported PCI Card Detected Remove PCI Card from Slot
- Unsupported Processor Configuration (Processor Required in Slot #1)
- Warning - Mixed Feature Processors Were Detected
- WARNING - Resetting Corrupted CMOS
- WARNING - Resetting Corrupted NVRAM
- WARNING - Resetting Corrupted System Environment
- WARNING - Restoring Default Configurations as Requested
- 207 - Invalid Memory Configuration Detected. DIMMs installed when no corresponding processor is detected.
- Introduction to POST error messages
- Electrostatic discharge
- Regulatory compliance notices
- Server specifications
- Technical support
- Acronyms and abbreviations
- Index