Document Outline

• Table of Contents
• About This Manual
  • Objectives
  • Audience
  • Document Organization
  • Related Documents
  • Documentation Conventions
    • Notes, Cautions, and Warnings
  • Contact Juniper Networks
  • Documentation Feedback
• Product Overview
  • System Overview
    • System Description
    • Field-Replaceable Units (FRUs)
    • G10 CMTS Features and Functions
      • Functional Overview
      • Broadband Cable Processor ASIC
    • G10 CMTS Components
    • G10 CMTS Management
    • G10 CMTS Hardware Overview
  • Hardware Component Overview
    • Chassis
      • Physical Characteristics
      • Card Cage and Midplane
      • Chassis Versions
      • Power Supplies
      • Power Transition Modules
      • Cooling and Fans
    • DOCSIS Module
      • Functional Characteristics
        • Data Packet Processing
          • Higher Layer Functions
          • MAC Layer Functions
          • Physical Layer Functions
        • Modem Management
          • MAC Layer Scheduling
          • Cable Modem Management
        • Enhanced Routing and Bridging Features
      • Physical and Electrical Characteristics
    • Chassis Control Module
      • Functional Characteristics
        • Configuration, State, and Alarm Data
      • Physical and Electrical Characteristics
    • NIC Module
      • Functional Characteristics
      • Physical and Electrical Characteristics
    • Chassis Rear Modules
      • NIC Access Module
      • HFC Connector Module
      • Switched I/O Module
      • Hard Disk Module
  • System Architecture Overview
    • JUNOSg Internet Software Overview
      • Routing Engine Software Components
        • Routing Protocol Process
          • Routing Protocols
          • Routing and Forwarding Tables
          • Routing Policy
        • Interface Process
        • SNMP and MIB II Processes
        • Management Process
        • Routing Engine Kernel
      • Tools for Accessing and Controlling the Software
      • Software Monitoring Tools
      • Software Installation and Upgrade Procedures
    • Data Path Processing
      • Downstream Data Path
      • Upstream Data Path
• Initial Installation
  • Prepare the Site
    • Safety Precautions
    • Notices
    • Power
      • AC Power
      • DC Power
    • Environment
    • Mounting
    • Tools and Equipment Required for Installation
    • Coaxial Cable Requirements
    • Characterization of Installation Site
    • Summary Checklist
    • Noise Measurement Methodology
      • Average Upstream Noise Measurement
      • Peak Upstream Noise Measurement
    • Additional Characterization Tables
    • Verification of Shipping Cartons
    • G10 CMTS Installation Checklist
  • Install the CMTS
    • Ground the Chassis
    • Rack Mounting
    • Install Power Supplies
    • Install a DOCSIS Module
    • Install an HFC Connector Module or SIM
    • Install a Chassis Control Module
    • Install a Hard Disk Module
    • Install a NIC Module
    • Install a NIC Access Module
    • Cable an HFC Connector Module or SIM
      • Cable the F-connector Ports
    • Cable a Chassis Control Module
    • Cable a NIC Module
    • Cable a NIC Access Module
    • Attach a PC to the Chassis Control Module
    • Connect to Power Sources
      • AC Power
      • DC Power
  • Connect the Power and Perform Initial Configuration
    • Power On the G10 CMTS
    • Power On and Configure the PC
    • Perform Initial Software Configuration
• Troubleshooting and Maintenance
  • RF Measurements
    • Downstream RF Measurement in CATV Mode
    • Downstream RF Measurement in Spectrum Analyzer Mode
    • Upstream RF Measurement
  • Troubleshooting
    • Features for Troubleshooting
      • Flap List
        • Use the Flap List for Troubleshooting
      • Local Event Log
      • Operational Commands
      • ServiceGuard Management System
    • CMTS Power and Booting Issues
      • CMTS Is Not Powering Up
      • CMTS Does Not Boot Successfully
      • CMTS Powers Down
    • Ideal HFC Plant Configuration Issues
      • Cable Modem Cannot Successfully Range
      • Cable Modem Cannot Establish IP Connectivity
      • Cable Modem Cannot Successfully Register
      • Cable Modem Throughput is Slow
      • Cable Modem is Dropped
    • HFC Plant Related Issues
      • Cable Modem Cannot Successfully Range
      • Cable Modem Throughput is Slow
  • Replacement Procedures
    • Power Supplies
      • Remove Power Supplies
    • Fan Trays
      • Replace a Fan Tray
        • Front Fan Trays
        • Rear Fan Tray
    • Module Removal
      • Remove a DOCSIS Module
      • Remove an HFC Connector Module or SIM
      • Remove a Chassis Control Module
      • Remove a Hard Disk Module
      • Remove a NIC Module
      • Remove a NIC Access Module
• Appendixes
  • Agency Certifications
    • Safety
    • EMC
    • Immunity
  • Radio Frequency (RF) Specifications
  • EIA Channel Plans
• Index
  • Index