Document Outline

• FMSteiw/FM-AM
• Receiver
  • Warning
    • For the customers in Canada
    • CAUTION :
    • Note to CATV system installer
  • Table of Contents
    • Remote control
    • Display
    • Electronic graphic equalizer
    • Surround sound system
    • Sound field
    • Dual room link control (DRLC)
  • Precautions
    • On safety
    • On operation
    • On cleaning the cabinet
    • For the customers in the U.S.A.
  • Installing
    • Notes on Installation
      • To prevent internal heat buildup in the unit,
      • Do not install the unit:
      • Do not place anything on top of the cabinet.
      • Do not throw away the carton and packing material!
    • Loading the Remote Commander with Batteries
      • To avoid damage caused by battery leakage and corrosion
      • Battery life
  • Connections
    • Notes on Connections
    • Connecting Audio Equipment
    • Connecting Video Equipment
    • 0 Connecting the FM Antenna
    • Connecting the AM Antenna
      • For areas with difficult AM reception
      • To prevent hum
  • Parts Identification
    • Front Panel
      • Amplifier and general section
      • Tuner section
      • Sound field control section
      • Q] Program control section (RM-P311 only)
      • [2} MODE selector
      • [3] Cursor control section
      • S] Sound control section
      • [H Amplifier section
      • [S Control for other equipment
      • E] SLEEP button
      • [H Tuner section
      • m RESET button (RM-P311 only)
  • Audio Adjustment
    • Adjusting Volume
      • To adjust volume
      • To reduce the sound to a low level temporarily (- 20 dB attenuation)
    • Adjusting Left and Right Sound Balance.
    • Selecting the Speaker System
      • IMPORTANT
  • Selecting a Program Source
    • 3 Adjust the volume.
    • To stop the demonstration
    • Labeling the Program source
      • 1 Select the program source.
      • 2 Select the INDEX mode.
      • Create an index name.
      • 4 Repeat Steps 1 to 3 for all other program sources you want to assign an index name to.
      • To display the selected function and its name you create
  • Radio Reception
    • Tuning in a Station Directiy — Direct Tuning
      • To correct the entered frequency
      • For entering AM frequencies, you need not enter the last “0”.
      • If you enter a frequency not covered by the tuning interval
      • When the entered number is not in the receivable frequency range
      • When an FM stereo program is noisy
    • Scanning Stations Automaticaliy — Auto Tuning
      • 2 Select FWI or AM.
      • 4 Repeat step 3 until the desired station is received.
      • If the automatic scan «»ops frequently (for FM reception only)
      • To select the signal level
      • To receive lower signals again
    • Presetting Stations — Station Preset
      • 2 Tune in the desired station.
      • 4 While the MEMORY indicator is on, select the memory page (A, B or C).
      • 5 While the MEMORY indicator is on, press the desired number.
      • Replacing a preset st.aiicn
      • Memorizing FM mode
    • Tuning in a Preset Station — Preset Tuning
      • 2 Select the desired preset station.
      • IMPORTANT
    • Labeling the Preset Stations — Index Input
      • Each station can be stored under only one index name
      • To display the frequency and index name of preset stations
    • Selecting a Station among the Preset Stations haying the Same index - Index Tuning
    • Receiving FM Simulcast TV programs
  • Audio Recording
    • Recording on an Audio Tape Deck or DAT Deck
      • 1 Select the desired program source with the FUNCTION selector.
      • 2 Set the tape (DAT) deck in the recording mode.
      • 3 Start the selected program source.
      • 1 Insert the recorded tape into tape deck 1 (or the DAT deck).
      • 2 Insert a blank tape into tape deck 2 and adjust the recording level.
      • 3 Press TAPE 1 or DAT to select the deck for playback.
      • Notes on recording
      • Monitoring the recorded sound
  • Video Recording
    • Video Tape Editing
      • Preparation
      • With theSTR-AV1070X
      • 1 Press EDIT VIDEO to select the playback-side VCR
      • 2 Press VIDEO 2/LD or VIDEO 3 to select the video signal to monitor on the monitor TV.
      • 3 Set the playback-side VCR to the playback mode.
      • 4 Set VCR 1 to the recording mode.
      • 3 Set VCR 1 to the recording mode.
      • Listening to an audio program during video tape editing
      • Recording a TV program
      • To switch the playback-side VCR during editing
      • To view the other video source(s) on the monitor TV during editing
      • Listening to an audio program during video tape editing
    • Adding New Sound on a Video Jape during Video Editing
    • Adding New Sound on a Video Tape during Video Editing
  • Using the Graphic Equalizer
    • Creating a Equalization Curve
      • Adjustable frequency bands and the effect of level
      • To defeat the equalizer effect
      • To make the equalization curve flat
  • Obtaining the Surround Effect
    • Available Types of Effects
    • Placement of Speakers for DOLBY PRO LOGIC Mode
      • NORMAL mode
      • WIDE mode
      • PHANTOM mode
      • NORMAL mode
      • WIDE mode
      • PHANTOM mode
      • 3CH mode
    • Adjusting the Speaker Level for Dolby Surround System
      • To adjust the level with a test tone signal
    • Listening with Surround Effect
      • To turn off the surround effect
  • storing the Sound Effect — Sound Field Memory
    • Effects that can be stored into the memory
    • Storing the Sound Field Setting
    • Calling up the Sound Field Setting
  • Enjoying Sound in Another Room
    • Overview
    • Connections
    • Operation
  • How to Use the Learning Function (STR-AV1070X only)
    • Programming Signals of Other Audio/Video Equipment with Programmable System Commander RM-P311
      • The two remote commanders must:
      • Number of signals that the commander can learn
      • Notes on programming
    • Controlling Equipment
      • When Sony equipment cannot be remote-controlled
      • If no signal has been programmed
      • Notes on Battery
      • If the equipment works incorrectly
  • Troubleshooting Guide
  • Specifications
    • Audio Power Specifications
    • Other Specifications
      • POWER OUTPUT AND TOTAL HARMONIC DISTORTION
      • Amplifier section
      • Video section
      • General
  • Quick Reference
    • Adjusting sound quality
    • Vìdeo Operations with the STR-AV1070X
    • Video Operations with the STR-AV970X