Document Outline

• 0-5178-CCR
• SECTION 1: GENERAL INFORMATION
  • 1.01 Notes, Cautions and Warnings
  • 1.02 Important Safety Precautions
  • 1.03 Publications
  • 1.04 Declaration of Conformity
• SECTION 2 SYSTEM: INTRODUCTION
  • 2.01 How To Use This Manual
  • 2.02 Equipment Identification
  • 2.03 Receipt Of Equipment
  • 2.04 Working Principle
  • 2.05 Power Source Specifications
  • 2.06 Input Wiring Specifications
  • 2.07 Power Source Feature Locations
• SECTION 2 TORCH: INTRODUCTION
  • 2T.01 Scope of Operating Manual
  • 2T.02 Specifications
  • 2T.03 Introduction to Plasma
• SECTION 3: INSTALLATION
  • 3.01 Unpacking
  • 3.02 Lifting Options
  • 3.03 Air Supply Connections
• SECTION 4 SYSTEM: OPERATION
  • 4.01 Control Panel
  • 4.02 Preparations for Operating
  • 4.03 Sequence of Operation
  • 4.04 Cut Quality
  • 4.05 General Cutting Information
• SECTION 5 SYSTEM: SERVICE
  • 5.01 General Maintenance
  • 5.02 Basic Troubleshooting Guide
• SECTION 5 TORCH: SERVICE
  • 5T.01 General Maintenance
  • 5T.02 Inspection and Replacement of Consumable Torch Parts
• SECTION 6: PARTS LIST
  • 6.01 Introduction
  • 6.02 Power Source Replacement Parts
  • 6.03 SL60 Replacement Parts
  • 6.04 Options and Accessories
• APPENDIX 1: CIRCUIT DIAGRAM
• Statement of Warranty
• GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
• SECTION 1: GENERAL INFORMATION
  • Table 1-1 - Protective Filters
• SECTION 2 SYSTEM: INTRODUCTION
  • Figure 2-1 - Power Source Dimensions & Weight
  • Figure 2-2 - Power Source Setup
  • Figure 2-3 - Power Source Rear View
• SECTION 2 TORCH: INTRODUCTION
  • Figure 2T-1 - SL60 Torch
  • Figure 2T-2 - Typical Torch Head Detail
  • Figure 2T-3 - Parts-in-Place Circuit Diagram for Hand Torch
• SECTION 3: INSTALLATION
  • Figure 3-1 - Gas Connection to Compressed Air Input
  • Figure 3-2 - Optional Single - Stage Filter Installation for Compressed Air Input
• SECTION 4 SYSTEM: OPERATION
  • Figure 4-1 - Front Control Panel
  • Figure 4-2 - Rear Controls
  • Figure 4-3 - SL60 Torch Parts
  • Figure 4-4 - Work Cable Connection
  • Figure 4-5 - Rear Panel with ON/OFF Switch
  • Figure 4-6 - Front Panel with Power ON/OFF Indicator
  • Figure 4-7 - Torch Trigger Release
  • Figure 4-8 - Standoff Distance
  • Figure 4-9 - Standoff Cutting
  • Figure 4-10 - Torch Trigger Release
  • Figure 4-11 - Drag Cutting
  • Figure 4-12 - Cut Quality Characteristics
  • Figure 4-13 - Side Characteristics of Cut
• SECTION 5 TORCH: SERVICE
  • Figure 5-1 - Torch Head O-Ring
  • Figure 5-2 - ATC O-Ring
  • Figure 5-3 - Consumable Parts
  • Figure 5-4 - Tip Wear
  • Figure 5-5 - Start Cartridge
  • Figure 5-6 - Electrode Wear
• SECTION 6: PARTS LIST
  • Parts 6-1 - Power Source
  • Parts 6-2 - Electrode Parts
• APPENDIX 1: CIRCUIT DIAGRAM
• SECTION 1: GENERAL INFORMATION
  • 1.01 Notes, Cautions and Warnings
• SECTION 2 SYSTEM: INTRODUCTION
  • 2.01 Working Principle
  • 2.02 Power Supply Specifications
• SECTION 2TORCH: INTRODUCTION
  • 2T.01 Scope of Manual
  • 2T.02 Specifications
  • 2T.03 Introduction to Plasma
• SECTION 3: INSTALLATION
  • 3.01 Unpacking
  • 3.02 Lifting Options
• SECTION 4 SYSTEM: OPERATION
  • 4.01 Control Panel
  • 4.02 Preparations For Operating
  • 4.03 Sequence of Operation
  • 4.04 Cut Quality
  • 4.05 General Cutting Information
• SECTION 5 SYSTEM: SERVICE
  • 5.01 General Maintenance
  • 5.02 Basic Troubleshooting Guide
• SECTION 5 TORCH: SERVICE
  • 5T.02 Inspection and Replacement of Consumable Torch Parts
• SECTION 6: PARTS LISTS
  • 6.01 Introduction
  • 6.02 Power Supply Replacement Parts
• APPENDIX 1: CIRCUIT DIAGRAM
• 0-5178-Rear