Document Outline

• CHAPTER 1 GENERAL INFORMATION
• CHAPTER 1 GENERAL INFORMATION
  • Safety
  • Warranty
• CHAPTER 2 PRODUCT DESCRIPTION
• CHAPTER 2 PRODUCT DESCRIPTION
  • Pressure measurement
  • Humidity and temperature measurement
  • C
• CHAPTER 3 GETTING STARTED
• CHAPTER 3 GETTING STARTED
  • Mounting
  • Electrical connections
  • Connecting the probe
• CHAPTER 4 COMMISSIONING
• CHAPTER 4 COMMISSIONING
  • Display and keypad
  • Operating modes
    • SMODE Selecting the sending mode
  • Software settings
    • SERI Serial bus settings
    • ECHO Setting the serial bus echo on/off
    • FORM Defining the output format
    • EFORM Defining the error output format
    • DFORM Defining the display format
    • PROMPT Setting the prompt outputting ON or OFF
    • UNIT Setting the pressure and temperature units
    • AVRG Setting the averaging time
    • INTV Setting the output interval
    • ADDR Setting the transmitter address (for POLL mode)
    • SCOM User specific SEND command
    • PSTAB Setting the pressure stability indicator
    • PDMAX Setting the pressure difference limit
    • KEYLOCK Setting the keyboard lock on/off
  • Hardware settings
• C
• CHAPTER 5 OPERATING
• CHAPTER 5 OPERATING
  • RUN and STOP modes
    • R Starting the continuous output
    • S Stopping the output
    • SEND Outputting a single message only
    • RESET Resetting the transmitter
  • POLL mode
    • SEND Outputting one single message
    • OPEN Setting a transmitter from POLL mode to STOP mode
    • CLOSE Setting a transmitter from STOP mode to POLL mode
  • SEND mode
• CHAPTER 6 CALIBRATION AND ADJUSTMENT
• CHAPTER 6 CALIBRATION AND ADJUSTMENT
  • Pressure
    • CORR Listing linear and multipoint pressure corrections
    • LC Linear pressure corrections
    • LCI Entering linear pressure corrections
    • MPC Multipoint pressure corrections
    • MPCI Entering multipoint pressure corrections
    • CALD Storing the date of calibration
  • Humidity
    • Humidity adjustment
  • Temperature
    • Offset
    • Gain
    • TXCI Entering corrections for HMP45D and PT100 temperature measurement
    • V0XCI Entering corrections for HMP45A-P temperature measurement
• C
• CHAPTER 7 SELF-TESTING AND PROBLEM HANDLING
• CHAPTER 7 SELF-TESTING AND PROBLEM HANDLING
  • Returning the serial communication parameters
  • Diagnostic commands
    • ? Basic information on the transmitter settings
    • VERS Software version
    • SNUM Serial number
    • ERRS Error message output
• C
• CHAPTER 8 TECHNICAL DATA
• CHAPTER 8 TECHNICAL DATA
  • Barometric pressure
    • Operating range
    • Accuracy class
  • Humidity
  • Temperature
    • HMP45A-P & HMP45D
    • Pt100 sensor head
  • General
  • Mechanics
    • Transmitter body
    • HMP45A-P and HMP45D
    • PT100 sensor head
    • Weight
    • Dimensions
      • Transmitter body
      • HMP45A-P & HMP45D
      • Pt100 sensor head
  • Electromagnetic compatibility
  • Accessories
• APPENDIX A OPTIONAL RS485/422 INTERFACE OF PTU200 TRANSMITTERS
• APPENDIX A OPTIONAL RS485/422 INTERFACE OF PTU200 TRANSMITTERS
• A
• APPENDIX B ASHTECH PORT A/B 16 PIN CONNECTOR
• APPENDIX B ASHTECH PORT A/B 16 PIN CONNECTOR
• APPENDIX B ASHTECH PORT A/B 16 PIN CONNECTOR
• A
• APPENDIX C NMEA DATA FORMAT
• APPENDIX C NMEA DATA FORMAT
  • GPS Commands
    • Serial number