Multiquip Control Box Replacement LS60TD - Manual (Page 6)

LS60TD anD LS600 — COnTROL bOX RepLaCemenT — Rev. #1 (03/23/12) — page 6
COnTROL paneL COmpOnenTS
Figure 8. Digital Control Panel Components
0
5 0 0
7 5 0
1000
12 5 0
1 5 0 0
2 0 0 0
0
5 0 0
7 5 0
1000
12
5 0
1 5 0 0
2 0 0 0
E M E RG ENCY S TO
P
ACCUMULATOR
PRESSURE
PUMPING
PRESSURE
1
2
4
5
6
10 9
7
3
8
12
11
13
OFF
ON
IGNITION
REMOTE
CONTROL
FLOW
DIRECTION
VOLUME
LOCAL FORWARD
AUTOMATIC JOG
RESET
SET
DECREASE INCREASE
SCROLL
JOG “A”
CYLINDER STROKE
JOG “B”
REVERSE
CENTER
OFF
REMOTE
START
1.„ emergency Stop button —„Press„emergency„stop„
button„ to„ stop„ pump„ in„ an„ emergency.„Turn„ knob„
counterclockwise„to„disengage„the„stop„button.
2.„ ignition Switch —„Insert„the„ignition„key„here„to„start„
the„engine.„Turn„the„key„clockwise„to„the„ON„position,„
then„continue„turning„clockwise„to„the„START„position„
and„ release.„To„ stop„ the„ engine„ turn„ the„ key„ fully„
counterclockwise„to„the„STOP„position.
3.„ Digital Readout Screen —„Displays„and„monitors„the„
various„functions„of„the„machine.
4.„ Scroll Switch —„ Allows„ the„ operator„ to„ scroll„ the„
various„readout„screens.
5.„ Reset Switch —„ Allows„ the„ operator„ to„ reset„ the„
stroke„counter.
6.„ Remote Cable Connector —„Insert„the„remote„control„
input„cable„into„this„connector.
7.„ Direction Control Switch —„This„2-position„switch„
controls„the„direction„of„flow„for„any„mix„in„the„pump.„„
The„ leftmost„ position„ sets„ the„ pumping„ direction„ to„
forward„and„the„rightmost„position„sets„the„pumping„
direction„to„reverse.
8.„ pumping Control Switch —„This„3-position„switch„
controls„ the„ pumping„ of„ the„ pump.„The„ rightmost„
position„(REMOTE)„is„for„use„with„the„remote„control„
unit,„ the„ leftmost„ position„ (LOCAL)„ is„ for„ normal„
pumping„ operation,„ and„ the„ centermost„ position„
(CENTER„OFF)„prevents„pumping.
9.„ Cylinder Stroke Control Switch —„This„2-position„
switch„ controls„ the„ pumping„ function.„The„ leftmost„
position„ (AUTOMATIC)„ sets„ the„ pump„ to„ automatic„
cycling.„Set„the„switch„to„this„position„for„normal„pump„
operation.
„ The„rightmost„position„(JOG)„changes„the„pump„from„
automatic„to„manual„cycling.„This„allows„the„cylinders„
to„ be„ manually„ cycled„ using„ the„ Manual„ Cylinder„
Jogging„Switch.
10.„ manual Cylinder Jogging Switch —„This„„2-position„
switch„allows„the„operator„to„manually„jog„the„cylinders„
to„assist„in„clearing„material„line„packs„and„is„used„to„
test„pumping„pressure.
„ The„ leftmost„ position„ jogs„ Cylinder„ “A”„ and„ the„
rightmost„position„jogs„Cylinder„“B”.
11.„ Stroke volume Control Switch —„ Increases„ or„
decreases„the„number„of„strokes„per„minute„of„the„
pump„(not„used„on„model„LS60TD).
12.„ accumulator pressure gauge —„ This„ gauge„
monitors„the„internal„pressure„of„the„Accumulator„tank.„
Normal„internal„pressure„should„read„approximately„
1750„PSI„during„pumping.
13.„ main pressure gauge —„This„ gauge„ monitors„
the„ system„ pressure„ while„ pumping„ material.„The„
maximum„pressure„rating„is„4400„PSI„±„50.