Motorola TMS320C6711D - Manual (Page 99)

TMS320C6711D
FLOATINGĆPOINT DIGITAL SIGNAL PROCESSOR
SPRS292 − OCTOBER 2005
99 POST OFFICE BOX 1443
•
HOUSTON, TEXAS 77251−1443
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 1 †‡ (see Figure 51)
NO.
GDPA−167
ZDPA−167
−200
−250
UNIT NO.
MASTER SLAVE
UNIT
MIN MAX MIN MAX
4 tsu(DRV-CKXH) Setup time, DR valid before CLKX high 12 2 − 6P ns
5 th(CKXH-DRV) Hold time, DR valid after CLKX high 4 5 + 12P ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 1
†‡ (see Figure 51)
NO. PARAMETER
GDPA−167
ZDPA−167
−200
−250
UNIT NO. PARAMETER
MASTER§ SLAVE
UNIT
MIN MAX MIN MAX
1 th(CKXH-FXL) Hold time, FSX low after CLKX high¶ H − 2 H + 3 ns
2 td(FXL-CKXL) Delay time, FSX low to CLKX low# T − 2 T + 3 ns
3 td(CKXH-DXV) Delay time, CLKX high to DX valid −3 4 6P + 2 10P + 17 ns
6 tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
−2 4 6P + 3 10P + 17 ns
7 td(FXL-DXV) Delay time, FSX low to DX valid L − 2 L + 6.5 4P + 2 8P + 17 ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = Sample rate generator input clock = 2P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
5
4
3 7 6
2 1
CLKX
FSX
DX
DR
Figure 51. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1