Connections (dtr-6.3), Signal flow – Integra DTR-5.3 User Manual
Page 20
20
Connections (DTR-6.3)
7. Connecting a DVD recorder or other digital video recording
device (VIDEO 2)
Using RCA video cables, connect the video output jack (composite)
of the device to the VIDEO 2 VIDEO IN jack of the DTR-6.3 and
connect the video input jack of the device to the VIDEO 2 VIDEO
OUT jack of the DTR-6.3. Or if the device has S video input and
output jacks, using S video cables, connect the S video output jack of
the device to the VIDEO 2 S VIDEO IN jack of the DTR-6.3 and
connect the video input jack of the device to the VIDEO 2 S VIDEO
OUT jack of the DTR-6.3. Or if the device has component video
outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2
jacks on the DTR-6.3.
With the initial settings of the DTR-6.3, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at “Input Setup”
→ “Component Video”
(see page 53).
Using RCA audio cables, connect the audio output jacks of the
device to the VIDEO 2 IN audio jacks of the DTR-6.3 and connect
the audio input jacks of the device to the VIDEO 2 OUT audio jacks
of the DTR-6.3. Make sure that you properly connect the left
channels to the L jacks and the right channels to the R jacks.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of
the DTR-6.3 depending on the type of connector on the device.
With the initial settings of the DTR-6.3, nothing is allocated as
the digital input source for VIDEO 2 (----).
If you connect the digital audio output, be sure to make the appropriate
changes at “Input Setup”
→ “Digital Input” (see page 53).
If the device has a digital input, connect it to the DIGITAL OUTPUT
(OPTICAL or COAXIAL) jack of the DTR-6.3 for digital recording
of the signal from the digital input of the DTR-6.3.
Note:
The output from the DIGITAL OUTPUT jack of the DTR-6.3 is only
the digital signal input to the DIGITAL INPUT jack.
8. Connecting a television monitor or projector (MONITOR
OUT)
The DTR-6.3 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
Using an RCA video cable, connect the video input jack (composite)
of the device to the MONITOR OUT VIDEO jack of the DTR-6.3.
Or if the device has an S video input jack, connect it to the
MONITOR OUT S VIDEO jack of the DTR-6.3 using an S video
cable. Or if the device has component video inputs, connect them to
the bank of COMPONENT VIDEO OUTPUT jacks on the DTR-6.3.
Note:
Note that the Setup Menu will only be displayed on the monitor
connected to MONITOR OUT and not those connected to the
COMPONENT VIDEO OUTPUT jacks.
L
REMOT
CONTRO
COAXIAL
OPTICAL
1
2
IN
IN
IN
IN
FRONT
SURR
CENTER
SUB
WOOFER
VIDEO 2
VIDEO 1
OUT
OUT
DIGITAL INPUT
VIDEO 2
DVD
MONITOR
OUT
DVD
TAPE
CD
SUBWOOFER
PRE OUT
L
R
R
VIDEO 3
VIDEO 1
V
VIDEO 3
OPTICAL
COAXIAL
DIGITAL
INPUT
IN
IN
IN
OUT
IN
DIGITAL
OUTPUT
IN
INPUT 1
INPUT 2
OUTPUT
COMPONENT VIDEO
L
R
PHONO IN
P
R
P
B
Y
GND
OUT
OUT
S
ANTENNA
FM 75
AM
IR OUT
56K
A
40K
B
ZONE 2
OUT
DC IN
24V 1A
12 V
TRIGGER
OUT
RS232
L
R
ZONE 2
LINE OUT
A
B
ZONE 2
I
OU
IR
8. TV monitor or projector
(MONITOR OUT)
Component video
input
S Video input
Video input
P
R
P
B
Y
7. DVD recorder, other digital
video recording device
(VIDEO 2)
R (red)
L (white)
R (red)
L (white)
Video input
S Video input
Video output
S Video output
Analog audio input
Analog audio output
: Signal flow