JVC RS-WP1WT - Manual (Page 10)

English
7
Turning the Power On and Off
Note:
The lighting condition for the “STANDBY” indicator and the display
differs depending on the power source being used, as follows:
Turning the System On —————
Press the STANDBY/ON button on the Unit or
the Remote Control.
• When the System is operated on batteries, press the
STANDBY/ON button on the Unit. It cannot be turned on with
the Remote Control.
The “STANDBY” indicator goes out when the System is operated
on AC power or car battery (DC12V).
The display comes on and the System is ready to continue in the
mode it was in when the power was last turned off.
■
For example, if the last thing you were doing was listening to a
CD, you are now ready to listen to a CD again. If you wish, you
can change to another source.
■
If you were listening to the Tuner last, the Tuner comes on
playing the station it was last set to.
Turning the System Off —————
Press the STANDBY/ON button again.
The “STANDBY” indicator lights up when the System is operated
on AC power or car battery (DC12V).
The contents of the display changes to the clock, and “CLOCK”
indicator and the time are displayed without backlighting.
Basic Operations
SLEEP
CLOCK TIMER TIMER ON/OFF
PROGRAM
RANDOM
REPEAT
BAND
DISPLAY
AHB PRO
REVERSE MODE MULTI CONTROL
FM MODE
REW FF
RM-SRSWP1U REMOTE CONTROL
TAPE TUNER C D
DOWN UP SET
AUX
VOLUME
BASS/ TREBLE
STAND BY/ON
AUTO PRESET
DISPLAY
AHB PRO
STANDBY/ON
BASS/TREBLE
VOLUME + / –
VOLUME
VOLUME
AUX
TU NE R
TA PE
CD
ASP
O P EN
O N E TO UCH R E C
MULTI CONTROL
REW FF
STANDBY
CD PORTABLE SYSTEM RS-WP1
BAND
STANDBY/ON
VOLUME + / –
A.P.OFF
A .P.OFF
STANDBY/ON
STAND BY/ON
STANDBY/ON STANDBY
STAND BY/ON
STANDBY/ON STANDBY
STANDBY
indicator
or
or
Power source
AC power or car
battery (DC12V)
Batteries
“STANDBY” indicator/Display
• The “STANDBY” indicator lights when the power is turned
off.
• Backlighting of the display is illuminated when power is
turned on.
• The “STANDBY” indicator does not light.
• Backlighting of the display is not illuminated. However, the
backlighting is illuminated for a few seconds after operation.
PHONES
PHONES
■
Some power is always consumed even though power is turned
off (called Standby Mode).
■
To switch off the System completely, unplug the AC adaptor
from the AC outlet. If no battery is loaded in the System and it
left with the AC adaptor unplugged (or when there is a power
failure) for more than 5 minutes, the clock will be reset to
“AM 12:00”.
AUTO POWER OFF function
This System incorporates the AUTO POWER OFF function which
automatically turns the System off when no sound has been
produced for more than 10 minutes. In consequence, when 10
minutes have elapsed without any operation after completion of CD
or Tape operation, the power of the System is turned off
automatically.
When the playback or recording operation is performed within 10
minutes, the count by the AUTO POWER OFF function is disabled,
but it starts again as soon as the playback or recording completes.
When operations other than playback or recording is performed, the
count by the AUTO POWER OFF function starts after the last
operation of this kind, and the system is turned off in 10 minutes if
no more operation is performed.
At 1 minute before the system is turned off by the AUTO POWER
OFF function, message “P.OFF” blinks in the display.
The AUTO POWER OFF function is not available in Tuner mode or
AUX mode.
To enable the AUTO POWER OFF function
Press the A.P.OFF button on the Unit for more than two seconds so
that “A.P.OFF” appears in the display.
To disable the AUTO POWER OFF function
Press the A.P.OFF button on the Unit for more than two seconds so
that “A.P.OFF” disappears from the display.