Jotul GF 200 DV - Manual (Page 8)

8
Install the Exhaust Restrictor Plate
1. Remove the Top Plate to access the Glass Panel.
2. Release the Glass Panel latches and lift the panel
straight up off of the firebox.
2. Carefully remove the Log Set pieces from the
firebox.
2. Use a 1/4” nut driver to remove the two lower
sheet metal screws located inside the firebox
below the exhaust outlet. Install the rectangular
restrictor plate over the lower half of the outlet
and secure it using the same screws.
Vent Restriction
The GF 200 DV Lillehammer includes two draft
restrictor plates found in the parts bag. These must
be installed togethe within the stove in the follow-
ing vent configurations:
1) ANY vertically vented installation
2) ANY horizontal vent utilizing a Snorkel
Termination.
Additional restriction may be necessary, depending
on the vent height.
The plates are used to compensate for draft
characteristics that would otherwise interfere with
proper burner performance such as low heat output,
weak flame picture, or inefficient combustion. Both
restrictors must be installed. See Figs. 6 and 7.
Exhaust
Outlet
Lower Exhaust Screws
Rectangular
Exhaust
Restrictor
Plate
Firebox
Exhaust
Baffle
Figure 6. Install the Exhaust Restrictor Plate.
SEALANT
Venting Requirements
There are three types of venting configurations
approved for use with the Lillehammer gas stove:
• Hearthmount Co-Linear (Vertical Termination)
• Vertical Venting (Vert ical Termination)
• Horizontal Termination (Horizontal Termination)
The Lillehammer is approved for use with the
vent systems listed below. Use parts of one manu-
facturer only - DO NOT MIX VENT COMPONENTS
FROM DIFFERENT MANUFACTURERS IN THE SAME
SYSTEM.
• Simpson Dura-Vent GS
• Amerivent Corporation
• Security Vent Ltd.
Installation of any components not manufac-
tured or approved by Jøtul or failure to meet all
clearance requirements will void all warranties and
could result in property damage, bodily injury, or
serious fire.
The approved vent configurations described in
this manual are derived from extensive testing
under controlled laboratory conditions. Gas appli-
ance performance can be negatively affected by
variables present in the installation environment, i.e:
atmospheric pressure, strong prevailing winds,
adjacent structures and trees, snow accumulation,
etc. These conditions should be taken into consider-
ation by the installer and stove owner when plan-
ning the vent system design.
IMPORTANT
• JOINT SEALING REQUIREMENT:
APPLY A 1/8” BEAD OF HIGH-
TEMPERATURE (750°F) SEAL-
ANT TO THE MALE SECTION OF
THE INNER VENT PIPE. SEE
FIG. 9. THE CEMENT
SHOULD FORM A SEAL
BETWEEN THE INNER
AND OUTER PIPES.
• NEVER MODIFY ANY
VENTING COMPONENT, OR USE
ANY DAMAGED VENTING PRODUCT.
• THE GAS APPLIANCE AND VENT SYSTEM MUST BE
VENTED DIRECTLY TO THE OUTSIDE OF THE
BUILDING AND NEVER ATTACHED TO A CHIMNEY
SERVING A SOLID FUEL OR GAS BURNING APPLI-
ANCE. EACH DIRECT VENT GAS APPLIANCE MUST
HAVE ITS OWN SEPARATE VENT SYSTEM. COM-
MON VENT SYSTEMS ARE PROHIBITED.
• IF VENTING SYSTEM IS DISASSEMBLED FOR ANY
REASON, REINSTALL PER THE INSTRUCTIONS
Install the Air Inlet Restrictor Plate
1. Using a 1/4” nut driver, remove the left hand
sheet metal screw holding the Air Deflector to
the rear wall of the firebox. See Fig. 7.
2. Slide the Air Inlet Restrictor down along the rear
wall of the firebox behind the Air Deflector, so
that the Restrictor plate completely covers the air
intake inlet.
3. Secure both the Restrictor plate and the Deflector
to the rear wall using the same screw.