JVC HD-DH5US - Manual (Page 45)

Masterpage:Right-FullCol
EN
45
Filename [HM-DH5U_Eng.fm]
H
Set recording speed
Press [REC SPEED] to set the recording speed.
I
Return to normal screen
Press [D E] to move the arrow to “CONFIRM”,
then press [OK].
“PROGRAM COMPLETED PRESS [TIMER] TO
ENTER TIMER STANDBY MODE” appears on the
screen, then press [OK] to return to normal
screen.
J
Engage timer recording standby
mode
Press [TIMER (j)].
The VCR turns off automatically and [j] is
displayed on the front display panel.
To timer-record daily or weekly serials
Press [DAILY] (number [8]) or [WEEKLY] (number [9])
anytime during steps
D through H .
“MON – FRI”, “MON – SAT”, “SUN – SAT” or
“EVERY _ _ _” appears on the Program screen.
• Pressing the button again makes the corresponding
indication disappear.
To use the VCR while it is in timer recording standby
mode
Press [TIMER (j)] to disengage the timer recording
standby mode, then press [POWER] to turn on the VCR.
DO NOT forget to re-engage timer recording standby
mode again by pressing [TIMER (j)] after you use the
VCR; otherwise, you cannot record the broadcast you
want.
• When “AUTO TIMER” (A page 66) is set to “ON”, the
timer recording standby mode is automatically engaged
when the VCR is turned off. It is temporarily canceled
when the VCR is turned on. You do not have to press
[TIMER (j)] to engage or disengage the timer recording
standby mode.
NOTES:
• Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time is lost if it lasts for more
than 10 minutes.
• As a result, when the power is supplied again to this VCR after
the power failure, the following will take place.
1. This VCR starts Auto Clock Set automatically to restore the
clock time.
2. If the clock time is restored correctly and “AUTO TIMER”
is set to “ON”, each timer program you have made will
start at its start time unless its end time has elapsed.
• Programs that start after midnight must have the next day’s
date.
• After timer recording is completed, the VCR turns off
automatically.
• You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
• If the tape reaches its end during timer recording, [j], [X], and
[E] blink.
• To timer-record cable or satellite channels, be sure to keep the
cable box or DBS receiver turned on.
ATTENTION FOR DBS RECEIVER USERS
“TV” : To timer-record a regular TV broadcast
received on the VCR.
“CATV” : To timer-record a cable TV broadcast
received on the VCR, or through a cable
box (unless “INPUT CH” is set to “OFF” on
Cable Set Up screen A page 23).
“DBS” : To timer-record a satellite broadcast
received through a DBS receiver.
NOTE:
If “BAND” is set to “TV” on the Tuner Set Up Screen
(
A page 21) and “INPUT CH” is set to “OFF” on Cable Set
Up screen ( A page 23), “CATV” will not be displayed on
the Program screen; If “BAND” is set to “CATV” or “INPUT
CH” is set to “ON” on Cable Set Up screen, “TV” will not be
displayed.
If the channel number entered requires that the band
be set, “7=DBS” is displayed on the screen.
If this happens, press the ‘Number’ key [7 (DBS)] to
select “DBS”.
If you are using a DBS
receiver (unless “INPUT
CH” is set to “OFF” on
DBS Receiver Set screen
A page 26), the band
indication (“TV”, “CATV”
or “DBS”) appears under
the channel number
indication (“SOURCE”).
CONFIRM CANCEL
10:00 PM
STD (SP)
110 CH
DBS
8:00 PM
START TIME STOP TIME DATE
DAILY/WEEKLY
CH
SOURCE
TIMER PROGRAM
REC SPEED
SET PROGRAM WITH [+/ , REC SPEED,7=DBS,
8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"
START STOP DATE CH EXIT
PROG.
3/24/04 (WED)
EVERY WED
HM-DH5U_Eng.fm Page 45 Friday, June 25, 2004 11:42 AM