JVC RX-7000RBK - Manual (Page 38)

35
English
Adjusting the Front Speaker Output Balance
(Also see page 13)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the
% / fi / @ / # buttons also displays the
MAIN MENU.
2. Press
% / fi to move
to “SOUND
CONTROL,” then press
@ / #.
The SOUND CONTROL menu appears.
3. Press
% / fi to move
to “BAL.” (Balance).
4. Press
@ / # to adjust
the balance.
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
Reinforcing the Bass
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the
% / fi / @ / # buttons also displays the
MAIN MENU.
2. Press
% / fi to move
to “SOUND
CONTROL,” then press
@ / #.
The SOUND CONTROL menu appears.
3. Press
% / fi to move
to “BASS BOOST.”
4. Press
@ / # to turn the
bass boost function
“ON” or “OFF.”
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
Attenuating the Input Signal
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the
% / fi / @ / # buttons also displays the
MAIN MENU.
2. Press
% / fi to move
to “SOUND
CONTROL,” then press
@ / #.
The SOUND CONTROL menu appears.
3. Press
% / fi to move
to “INPUT ATT.”
4. Press
@ / # to turn the
Input Attenuator mode
“ATT ON” or
“NORMAL.”
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
Adjusting the Subwoofer Output Level
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the
% / fi / @ / # buttons also displays the
MAIN MENU.
2. Press
% / fi to move
to “SOUND
CONTROL,” then press
@ / #.
The SOUND CONTROL menu appears.
3. Press
% / fi to move
to “SUBWFR LEVEL.”
4. Press
@ / # to adjust
the subwoofer output
level.
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
Adjusting the DSP Modes
(Also see pages 28 – 31)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the
% / fi / @ / # buttons also displays the
MAIN MENU.
2. Press
% / fi to move
to “MODE.”
3. Press
@ / # to select the
DSP mode you want to
adjust.
• In this example,
“THEATER” is selected.
4. Press % / fi to move
to “SOUND
CONTROL,” then press
@ / #.
The SOUND CONTROL
menu appears.
5. Press
% / fi to move
to “SURROUND
LEVEL,” then press
@ / #.
The SURROUND LEVEL
menu appears.
6. Press
% / fi to move
to the item you want to
set or adjust, then press
@ / #.
On these adjustment menus, you can do the following:
For 3D-PHONIC (3D ACTION, 3D THEATER) :
“DSP EFFECT”: Select the effect level.
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
BASS BOOST : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
MAIN MENU
SOURCE :VCR
VISUAL :VCR
MODE :THEATER
SOUND CONTROL
TUNER CONTROL
SETTING
VOLUME : 20
:OPERATE
SURROUND LEVEL
:OPERATE
TEST TONE : OFF
CENTER LEVEL: 0dB
REAR L LEVEL: +6dB
REAR R LEVEL: 4dB
DSP EFFECT : 3
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
BASS BOOST : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:ENTER
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
BASS BOOST : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
BASS BOOST : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
BASS BOOST : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
EN34_44.RX-7000R[E]/f 00.4.24, 3:03 PM 35